Lower Deflector!

[ZSHO]

I noticed the Front Lower Deflector located right under the Front Bumper area does not provide a sufficient seal on the bottom sides of the vehicle and acts as a cleavage instead,while letting water intrusion and such contaminants enter the Undercarriage structure of the vehicle..

Has anyone tried Sealing the small exposed sections with some (PVC) Polyvinyl Chloride type plastic material for a better overall seal!!
This was discovered while trying to remove my ALKY PUMP the other day..

The part in Question is pictured below..Thanks. Z

https://parts.levittownfordparts.com/oem-parts/ford-lower-deflector-ag1z8327a/?c=Zz1ib2R5JnM9cmFkaWF0b3Itc3VwcG9ydCZpPUpOMTAwMzE1JnI9NyZhPWZvcmQmbz10YXVydXMmeT0yMDEzJnQ9c2hvJmU9My01bC12Ni1nYXM%3D

[shaundizzle15]

Funny you mention this, I haven't tried to seal it however I was thinking about a one piece lower cover. Essentially something that would remove that piece and the piece that covers the oil filter etc, with one streamlined piece. Seemed like it would help aero and prevent the contamination your talking about.

[ZSHO]

I was able to obtain a PIC for reference,right under the Reservoir Tank and also Under the Drivers side there is a Good portion of the (Under cover) exposed to the Driveway Floor letting water & such contaminants enter the under carriage of the vehicle.

The point i'm trying to make is for anyone running Methanol Injection as the Meth Pump is more exposed and susceptible to water intrusion even with Condom sleeve of the pump on could ultimately lead to failure IMO!  Z

[Sabtaj1]

I had my meth pump mounted up inside the bumper on my flex near the washer res.  I would recommend finding a better mounting option.  I had my pumps fail twice mounted there.  Second time it happened I was tuned a little hot on e85 mix and blew 4 large holes in the block and had a whole piston just sitting on top of the PTU when I dropped the engine.  It was cute....  Maybe look into making some type of enclosure for it.  I wish I would have made something. 

[ZSHO]

To Cold out now,but do have some extra PVC Plastic lying around and will put it to good use. Z   

[autobahn terror]

I had my meth pump mounted up inside the bumper on my flex near the washer res.  I would recommend finding a better mounting option.  I had my pumps fail twice mounted there.  Second time it happened I was tuned a little hot on e85 mix and blew 4 large holes in the block and had a whole piston just sitting on top of the PTU when I dropped the engine.  It was cute....  Maybe look into making some type of enclosure for it.  I wish I would have made something.

Not to revel in your misfortune or anything, but do you have some pictures of the carnage?

[Sabtaj1]

Plus holes all over the oil pan area.  Damn thing still ran too.  LOL  was just a little shaky but you woulda thought it was a diesel with hoe much oil ended up coming out of it. 

[TopherSho]

Plus holes all over the oil pan area.  Damn thing still ran too.  LOL  was just a little shaky but you woulda thought it was a diesel with hoe much oil ended up coming out of it.

....... wwooooooowwwww....

[TopherSho]

Plus holes all over the oil pan area.  Damn thing still ran too.  LOL  was just a little shaky but you woulda thought it was a diesel with hoe much oil ended up coming out of it.

Now I HAVE to ask, who was the tuner?  PM me if you don't feel going public.  We all know that pre-DEt is bad,  but your timing must have been insanely high and did not compensate for ping when it detected it.  that is CRAZY bad levels of detonation to chuck the whole piston cap out the side...

[SM105K]

Plus holes all over the oil pan area.  Damn thing still ran too.  LOL  was just a little shaky but you woulda thought it was a diesel with hoe much oil ended up coming out of it.

Now I HAVE to ask, who was the tuner?  PM me if you don't feel going public.  We all know that pre-DEt is bad,  but your timing must have been insanely high and did not compensate for ping when it detected it.  that is CRAZY bad levels of detonation to chuck the whole piston cap out the side...

Exactly why I refuse to use meth as secondary fuel system.  I learned my lesson many years ago with Nitrous.  Lost a fuel solenoid on a kit and ended up losing a couple of pistons.  Thank God it was just a SBE 302 with AFR Heads and a Nitrous cam, so it wasn't expensive to swap and replace the parts, it just cost me a grand because I lost the race. 

[ZSHO]

I was curious if anyone can see the ^^^ PICS kindly posted by Sabtaj1! TIA.Z
I tried to restore any PB PICS!

[SHOdded]

No problems here.  PB has stopped preventing people from seeing pics, watermarking them instead.

[TopherSho]

Plus holes all over the oil pan area.  Damn thing still ran too.  LOL  was just a little shaky but you woulda thought it was a diesel with hoe much oil ended up coming out of it.

Now I HAVE to ask, who was the tuner?  PM me if you don't feel going public.  We all know that pre-DEt is bad,  but your timing must have been insanely high and did not compensate for ping when it detected it.  that is CRAZY bad levels of detonation to chuck the whole piston cap out the side...

Exactly why I refuse to use meth as secondary fuel system.  I learned my lesson many years ago with Nitrous.  Lost a fuel solenoid on a kit and ended up losing a couple of pistons.  Thank God it was just a SBE 302 with AFR Heads and a Nitrous cam, so it wasn't expensive to swap and replace the parts, it just cost me a grand because I lost the race.

With Brads tune I am not as concerned about sudden meth loss.  IIRC unless you have modified the spark behavior (how much to drop on knock;  how quick to drop; how fast to try to recover) the ECU should stop catastrophic damage with just meth.   With the meth i only run 4-5 degrees more timing,  if it drops octane suddenly i suspect the ECU would correct it extremely fast.  Brad would need to comment more ..

[ZSHO]

I was curious how many of you running Meth in the colder Frigid winter months!
I might start a separate Topic on this discussion! Z

[SM105K]

Plus holes all over the oil pan area.  Damn thing still ran too.  LOL  was just a little shaky but you woulda thought it was a diesel with hoe much oil ended up coming out of it.

After buying the intercooler, and then the Extreme HPFP down the road...the only thing that would interest me in meth is cleaning the valves.
Now I HAVE to ask, who was the tuner?  PM me if you don't feel going public.  We all know that pre-DEt is bad,  but your timing must have been insanely high and did not compensate for ping when it detected it.  that is CRAZY bad levels of detonation to chuck the whole piston cap out the side...

Exactly why I refuse to use meth as secondary fuel system.  I learned my lesson many years ago with Nitrous.  Lost a fuel solenoid on a kit and ended up losing a couple of pistons.  Thank God it was just a SBE 302 with AFR Heads and a Nitrous cam, so it wasn't expensive to swap and replace the parts, it just cost me a grand because I lost the race.

With Brads tune I am not as concerned about sudden meth loss.  IIRC unless you have modified the spark behavior (how much to drop on knock;  how quick to drop; how fast to try to recover) the ECU should stop catastrophic damage with just meth.   With the meth i only run 4-5 degrees more timing,  if it drops octane suddenly i suspect the ECU would correct it extremely fast.  Brad would need to comment more ..

With purchase of the GH IC and an new Extreme HPFP, would meth even be needed anymore except for the valve cleaning properties?