First SHO With Direct Port Methanol injection!!

[StealBlueSho]

So if he gets pulled over on the way home the cops have no idea ;-) Safe travels Z!!!

[StealBlueSho]

On a serious note however.... did they give you any indication if the port injection allowed them to get more power out of the kit since the meth is more evenly distributed? Or is it more a CYA at this point?

[ZSHO]

On a serious note however.... did they give you any indication if the port injection allowed them to get more power out of the kit since the meth is more evenly distributed? Or is it more a CYA at this point?

IIRC Minimal gains were expected with the new Direct port setup.
But it does allow you to run a safer more reliable and effective Tune since the new setup allows for an equal amount methanol to be evenly dispersed in each port/cylinder. Z

[J-Will]

Do they test/ adjust at each cylinder at all after they drill/ tap the manifold?  Or do they assume that the block evenly distributes 6 different ways?

[ZSHO]

My SHO was petty much a test vehicle for the newly developed Direct port setup and found out in the later stages of the install that some additional components were needed for install such as an Alky solenoid and module/line/compressor fittings in order for the Methanol to travel accordingly through each port. Z
I will try to post some pics of the solenoid/module.

[TopherSho]

My SHO was petty much a test vehicle for the newly developed Direct port setup and found out in the later stages of the install that some additional components were needed for install such as an Alky solenoid and module/line/compressor fittings in order for the Methanol to travel accordingly through each port. Z
I will try to post some pics of the solenoid/module.

I'm loving the 1 screw 3-bar

Looking pretty dam slick though, i eagerly await your break in and initial runs..

[StealBlueSho]

That MY SHO only had one screw... the other side is a post..

[Vortech347]

I'm loving the 1 screw 3-bar

Looking pretty dam slick though, i eagerly await your break in and initial runs..

My 13' only has one screw on the MAP sensor as well. 

[panther427]

His sleeper has a sleeper mod. Excellent addition to your car

[MKspool]

I believe aqua mist has the most advanced Controller and part configuration for direct port on direct injected engines. Might want to check out how they're system works too see if it can help you dial it in.

I plan on putting their system on my mks soon.

[ZSHO]

I believe aqua mist has the most advanced Controller and part configuration for direct port on direct injected engines. Might want to check out how they're system works too see if it can help you dial it in.

I plan on putting their system on my mks soon.

@MKspool Please educate me how more advanced part configuration aqua mist has!!!!!!! Since my SHO was a Test vehicle for this new setup. Z

[StealBlueSho]

I believe aqua mist has the most advanced Controller and part configuration for direct port on direct injected engines. Might want to check out how they're system works too see if it can help you dial it in.

I plan on putting their system on my mks soon.

@MKspool Please educate me how more advanced part configuration aqua mist has!!!!!!! Since my SHO was a Test vehicle for this new setup. Z

Subscribed for this one....

[ZSHO]

Here is a quick summary/recap after a weeks time with the newly Direct Port injection Setup!!!
The car is absolutely a (Beast)and cant wait to finally get her to the Track and have it unleashed,"Time Slips" to follow.
These are the items that are needed to complete the install for anyone interested.


6 M-15 Nozzles and 6 Adapter's for Direct Port Methanol Plumbing.
6 Cylinder Tubing Kit with B-Nuts and Sleeves.
1 IN 6 Out Distribution Block.
1/8 NPT X 3/16 Compression Fitting.
Alky Solenoid/Module,Line and Fittings.

The Alky Solenoid/Module acts as a Check Valve which progresses the way the Methanol is to Travel into the Direct Port Lines.

I have been working with Julio from Alky control which has been IMHO a True pleasure to Deal with,especially with his Customer Service and Support is by far second to none in conjunction with LMS on installing and adding an additional 7TH INJECTOR at the outlet of the (intercooler) which will provide lower air charge temps prior to the intake manifold and IAT sensor.

I will have more information once it is readily available once completed and installed since my SHO was a Test vehicle on this Platform. Z

FWIW I know their are similar Kits readily available from Pro-Meth and others but they DO NOT Include/provide many of the items mentioned above in order to complete this new Direct Port Setup. Z

[StealBlueSho]

Sounds beastly!!!!

[jbeez]

That's sexy

Sent from my Nexus 6P using Tapatalk