October 01, 2020, 03:55:30 AM
collapse
collapse

Author Topic:  "How-To" SHO and Flex convert to vent to atmosphere with factory blow off valves  (Read 747797 times)

Offline EcoPowerParts

  • How can I help you today?
  • Vendor
  • Elite Member
  • *
  • Phoenix
  • Thank You
  • -Given: 147
  • -Received: 1240
  • Posts: 3057
    • EcoPowerParts
  • Liked:
  • Likes Given: 0
I just converted my factory BoV to FTA on my Flex today.
What does this do for you?
Nothing but making a PFFFFT noise when you lift the throttle under boost.
Is there any downsides to this?
No, the car is speed desnsity so releasing the air from the turbos to atmosphere when the blow off valves open does not negatively impact the tune, factory or modified.

BTW, I couldn't find 1" vacuum "nipples" to block off the factory tubing so I went to Home Depot and searched around, found some 1" rubber chair leg "tips" to use, worked pretty good so far.

Front Blow off Valve and blocked off tube



Another shot of the factory Blow off Valve with the return tube removed - vent to atmosphere


Close up of rear portion of intake tubing with blow off valve return hose removed and blocked off. For me easiest way to get to this area and remove tubing was to remove the intake tubing and rotate to access the clamp that held the tubing onto the blow off valve.



Rear Blow off Valve



Complete turbo to intercooler pipe with Blow off Valves circled


EDIT: Found some rubber caps to use instead of rubber chair leg bottoms
http://www.mcmaster.com/#92805K28

Updated pictures with the new caps on from mcmaster - didn't know they were going to be red :(
« Last Edit: July 14, 2013, 12:58:42 PM by 4DRHTRD »
Mike B | info@ecopowerparts.com
www.ecopowerparts.com -
 please use my website for any price quotes and to submit any orders.
Please email me via info@ecopowerparts.com if you have any questions on new or existing orders, PM's via the forum are hard to track your purchase as I can't relate user name to actual name.
https://www.facebook.com/ecopowerparts

Offline PopolZ

  • Full Member
  • *
  • Saint-Hubert, Qc - Peoples Republic of Canuckistan
  • Thank You
  • -Given: 6
  • -Received: 10
  • Posts: 170
  • Ecobooster & RB26ster
  • Liked:
  • Likes Given: 0
On the SHO we already have the PFFFFT because of the "noise generator". Mine is sitting in the trunk since it's been replaced with an HKS SSQV III BOV.
2010 Ford Taurus SHO, non-PP, Steel Blue #243 of 301 - Custom tune by Torrie@Unleashed, PPE non-catted downpipes, custom 3rd cat & resonator delete, water/meth injection, HKS SSQV3 BOV and Carbotech AX6 brake pads.

1991 Nissan Skyline GTR, Pearl Black Metallic - a few goodies

Offline bnoon

  • Full Member
  • *
  • Thank You
  • -Given: 0
  • -Received: 5
  • Posts: 150
  • Ecobooster
  • Liked:
  • Likes Given: 0
I just disconnected mine last night and took a trip around the block to make sure it didn't have any issues before I started buying intake parts.

Offline EcoBrick Bob

  • Elite Member
  • *
  • Naples, FL and Clear Lake, IA
  • Thank You
  • -Given: 62
  • -Received: 101
  • Posts: 1138
  • Liked:
  • Likes Given: 0
WHY?

"What difference does it make?"  (H. Clinton)  LOL :bangin:
2010 Red Candy/White EB Flex.. World's first 12 second Brick.. 12.904 @ 106.85 MPH - October 2011
2009 Spt. Red G8 GT - modded. best time 12.074 & 114.02 MPH
2008 White G8 GT - mods... 8.32 1/8 mi.

Naples, FL & Clear Lake, IA
Bob has decided not to post here any more, please do not PM him he will not receive it.

Offline EcoPowerParts

  • How can I help you today?
  • Vendor
  • Elite Member
  • *
  • Phoenix
  • Thank You
  • -Given: 147
  • -Received: 1240
  • Posts: 3057
    • EcoPowerParts
  • Liked:
  • Likes Given: 0
On the SHO we already have the PFFFFT because of the "noise generator". Mine is sitting in the trunk since it's been replaced with an HKS SSQV III BOV.

I just looked up an article on the BoV installation on your guys car.
So, now I'm looking at buying a SHO intake tube that goes from TB to IC and then have Paul make a tube that replaces the SHO/Flex back turbo to IC tube with no holes in it for BoV.
This way an aftermarket BoV can be added to the intake tract and the factory BoV can be removed entirely.
We're looking at a way to make a plug and play resistor to replace the factory BoV as well so no CEL

Hmm that part is AA5Z-6F073-B - $110... More research to do :)
« Last Edit: May 09, 2013, 10:39:30 AM by 4DRHTRD »
Mike B | info@ecopowerparts.com
www.ecopowerparts.com -
 please use my website for any price quotes and to submit any orders.
Please email me via info@ecopowerparts.com if you have any questions on new or existing orders, PM's via the forum are hard to track your purchase as I can't relate user name to actual name.
https://www.facebook.com/ecopowerparts

Offline bnoon

  • Full Member
  • *
  • Thank You
  • -Given: 0
  • -Received: 5
  • Posts: 150
  • Ecobooster
  • Liked:
  • Likes Given: 0
WHY?

"What difference does it make?"  (H. Clinton)  LOL :bangin:

The reason I'm doing it is to make super shorty intakes, basically just filters on the turbos. I don't care about IAT, only boost temps. This will simplify and eliminate a lot of hardware real estate under the hood for when I go liquid to air intercooler.

Offline EcoPowerParts

  • How can I help you today?
  • Vendor
  • Elite Member
  • *
  • Phoenix
  • Thank You
  • -Given: 147
  • -Received: 1240
  • Posts: 3057
    • EcoPowerParts
  • Liked:
  • Likes Given: 0
WHY?

"What difference does it make?"  (H. Clinton)  LOL :bangin:

The reason I'm doing it is to make super shorty intakes, basically just filters on the turbos. I don't care about IAT, only boost temps. This will simplify and eliminate a lot of hardware real estate under the hood for when I go liquid to air intercooler.
Keep me in the loop on this, I'm looking at doing that after I get fueling/turbos installed in a month or two.
Mike B | info@ecopowerparts.com
www.ecopowerparts.com -
 please use my website for any price quotes and to submit any orders.
Please email me via info@ecopowerparts.com if you have any questions on new or existing orders, PM's via the forum are hard to track your purchase as I can't relate user name to actual name.
https://www.facebook.com/ecopowerparts

Offline EcoPowerParts

  • How can I help you today?
  • Vendor
  • Elite Member
  • *
  • Phoenix
  • Thank You
  • -Given: 147
  • -Received: 1240
  • Posts: 3057
    • EcoPowerParts
  • Liked:
  • Likes Given: 0

Video
Mike B | info@ecopowerparts.com
www.ecopowerparts.com -
 please use my website for any price quotes and to submit any orders.
Please email me via info@ecopowerparts.com if you have any questions on new or existing orders, PM's via the forum are hard to track your purchase as I can't relate user name to actual name.
https://www.facebook.com/ecopowerparts

Offline bnoon

  • Full Member
  • *
  • Thank You
  • -Given: 0
  • -Received: 5
  • Posts: 150
  • Ecobooster
  • Liked:
  • Likes Given: 0
WHY?

"What difference does it make?"  (H. Clinton)  LOL :bangin:

The reason I'm doing it is to make super shorty intakes, basically just filters on the turbos. I don't care about IAT, only boost temps. This will simplify and eliminate a lot of hardware real estate under the hood for when I go liquid to air intercooler.
Keep me in the loop on this, I'm looking at doing that after I get fueling/turbos installed in a month or two.

Sure will. Do you know the turbo's factory inlet diameter? Looks to be around or just under 2 inches but I can't tell for sure without disassembly.

Offline EcoPowerParts

  • How can I help you today?
  • Vendor
  • Elite Member
  • *
  • Phoenix
  • Thank You
  • -Given: 147
  • -Received: 1240
  • Posts: 3057
    • EcoPowerParts
  • Liked:
  • Likes Given: 0
I don't think even 2", I'll have my stock-upgraded turbos back soon I'll take a measurement. In discussing the factory IC, I think I can pick up another 30+HP just by going with a water to air IC, I've been considering installing the heat exchanger in place of the factory IC as there will be space there, just need to find a core that is sized appropriately for that.
I'm going to be putting my water resevior in the rear spare tire area, I'm going to have a custom nitrous tank/water resevior built for back there when I do the IC upgrade.
Mike B | info@ecopowerparts.com
www.ecopowerparts.com -
 please use my website for any price quotes and to submit any orders.
Please email me via info@ecopowerparts.com if you have any questions on new or existing orders, PM's via the forum are hard to track your purchase as I can't relate user name to actual name.
https://www.facebook.com/ecopowerparts

Offline bnoon

  • Full Member
  • *
  • Thank You
  • -Given: 0
  • -Received: 5
  • Posts: 150
  • Ecobooster
  • Liked:
  • Likes Given: 0
Since I don't go full bore racing with mine, I won't even have a remote resevoir for mine. Just the largest h\e I can fit and a small overflow bottle for the pressure release lid.

Offline EcoBrick Bob

  • Elite Member
  • *
  • Naples, FL and Clear Lake, IA
  • Thank You
  • -Given: 62
  • -Received: 101
  • Posts: 1138
  • Liked:
  • Likes Given: 0
Don't quote me, but I think I remember Darreli saying the inlet is        1 1/2" as the Hennessey CAI system he bought a couple years ago didn't have a reducer/taper and just went from 2" to 1 1/2".
2010 Red Candy/White EB Flex.. World's first 12 second Brick.. 12.904 @ 106.85 MPH - October 2011
2009 Spt. Red G8 GT - modded. best time 12.074 & 114.02 MPH
2008 White G8 GT - mods... 8.32 1/8 mi.

Naples, FL & Clear Lake, IA
Bob has decided not to post here any more, please do not PM him he will not receive it.

Offline EcoBrick Bob

  • Elite Member
  • *
  • Naples, FL and Clear Lake, IA
  • Thank You
  • -Given: 62
  • -Received: 101
  • Posts: 1138
  • Liked:
  • Likes Given: 0
With your nitrous system you might get that extra HP, but my MCT temps running 75% methanol went below outside temp, so not sure how much cooler one could go with liquid IC, unless the liquid would be at a temp much below ambient.  Guess one could cool it with A/C system..
2010 Red Candy/White EB Flex.. World's first 12 second Brick.. 12.904 @ 106.85 MPH - October 2011
2009 Spt. Red G8 GT - modded. best time 12.074 & 114.02 MPH
2008 White G8 GT - mods... 8.32 1/8 mi.

Naples, FL & Clear Lake, IA
Bob has decided not to post here any more, please do not PM him he will not receive it.

Offline EcoPowerParts

  • How can I help you today?
  • Vendor
  • Elite Member
  • *
  • Phoenix
  • Thank You
  • -Given: 147
  • -Received: 1240
  • Posts: 3057
    • EcoPowerParts
  • Liked:
  • Likes Given: 0
Another video
Mike B | info@ecopowerparts.com
www.ecopowerparts.com -
 please use my website for any price quotes and to submit any orders.
Please email me via info@ecopowerparts.com if you have any questions on new or existing orders, PM's via the forum are hard to track your purchase as I can't relate user name to actual name.
https://www.facebook.com/ecopowerparts

Offline EcoBrick Bob

  • Elite Member
  • *
  • Naples, FL and Clear Lake, IA
  • Thank You
  • -Given: 62
  • -Received: 101
  • Posts: 1138
  • Liked:
  • Likes Given: 0
I would do this only if it will make "LOUD FART SOUNDS"... :biggrin:
2010 Red Candy/White EB Flex.. World's first 12 second Brick.. 12.904 @ 106.85 MPH - October 2011
2009 Spt. Red G8 GT - modded. best time 12.074 & 114.02 MPH
2008 White G8 GT - mods... 8.32 1/8 mi.

Naples, FL & Clear Lake, IA
Bob has decided not to post here any more, please do not PM him he will not receive it.

 

* Recent Topics

Re: Oct 16,17,18 Fords at M.I.R.
by bamsho | September 30, 2020, 06:38:59 PM
Anybody heading to this event?? I'M thinking about taking the fiv...
Re: Light to mid throttle boost surge
by TopherSho | September 30, 2020, 06:23:49 PM
In the image, Throttle request stays near flatthrottle body dipsboost ...
Re: Turbo Interchangeability
by xartic1 | September 30, 2020, 05:48:21 PM
The 2.7T in the Fusion Sport or the 3.0T in the MKZ would be more of a...
Re: Ride of The Month September 2020!!!
by StealBlueSho | September 30, 2020, 05:05:31 PM
LAST DAY TO SUBMIT AND VOTE!!! Get her done!! https://i.ibb.co/fq2Zc3...
Re: The 2020 28th National SHO Convention is in the books!
by StealBlueSho | September 30, 2020, 04:57:49 PM
Awesome read and I apologize for not being able to make it this year! ...
Re: HOW-TO: Removal And Installation Of The Intake Manifold
by Ecoboost_xsport | September 29, 2020, 09:23:25 PM
Damn it does look awesome and love the garage setup and protection on ...
Re: HOW-TO: 3.5L XDI +30% Fuel Injector Installation
by Ecoboost_xsport | September 29, 2020, 09:22:42 PM
Extremely detailed as well as informative write up....literally just n...
Re: Performance Shops in Chester County, PA area
by MattC | September 29, 2020, 08:44:30 AM
Apparently my notifications are off *facepalm*I've been dataloggi...
Re: AC Compressor pulley replacement
by Macgyver | September 28, 2020, 04:29:11 PM
I ended up replacing the entire compressor with a reman unit. I also r...
Re: SHO vs Hellcat Redeye
by Macgyver | September 27, 2020, 09:17:56 PM
I have heard the Nittos are a great tire for traction. Road in a Juke ...
Official Forum Sponsor of Ecoboost Performance Forum

SimplePortal 2.3.5 © 2008-2012, SimplePortal