July 08, 2020, 10:19:59 PM
collapse

Author Topic: FMIC Install/Routing  (Read 123 times)

Offline GotGrip?

  • The work around guy
  • Jr. Member
  • *
  • Minnesota
  • Thank You
  • -Given: 7
  • -Received: 13
  • Posts: 17
  • The Dude
FMIC Install/Routing
« on: June 29, 2020, 12:23:06 PM »
So in the beginning of this adventure I had an idea to test Bar/plate vs Tube/Fin style intercoolers and the results are basically T/F sucks, I do have some pictures of that cooler on the vehicle, but ultimately the IAT2 temp was higher at all points in the rpm range. The cooler shown in these pictures was removed and replaced with a Treadstone TR8C (they are both B/P style but TR was more efficient).  So now that you have some back story, here's some photos!

If you're looking for a one stop shop kit there is a user now selling them so you don't have to spend the time piecing all together. If anyone has questions, I will try to do my best to answer them!

Yes, the stock Intercooler is out, and there is a little bit of minor trimming, shouldn't take more than 15 mins all together to do.

(Sorry for the delay getting this posted, been having issues with photos!)

« Last Edit: June 29, 2020, 02:21:34 PM by GotGrip? »
2016 SHO Non-PP, GH/AJP E30 Tune,3Bar MAP, K&N Typoon, EPP Noisemaker Delete, MSD Coils, Catch Can, H&R Springs, ZEDD SL5 19x9.5, PS Drilled/Slotted rotors, FMIC Intercooler, SSM Trans Mounts, TCE Custom Catted DPs.

Current Dyno: 421/503 (pre-dp)

Upcoming -  Intercooler Sprayer, XDI35

Offline SM105K

  • IG @egocheckersho
  • Forum Supporters
  • Elite Member
  • *
  • *
  • Arizona
  • Thank You
  • -Given: 943
  • -Received: 1105
  • Posts: 1235
  • Thee Forum Cowboy
Re: FMIC Install/Routing
« Reply #1 on: June 29, 2020, 12:24:58 PM »
Is the AC still functioning normal like before?
"M" 2013 SHO PP | AJPTurbo E30 Tune | GH Intercooler | PPE Downpipes | Custom Magnaflow Resonator | 3rd Cat Delete | Dicunzolo Gen2 Trans Mounts| EPP Noisemaker Eliminator | MSD Coil Over Plugs | SP-542's | UPR Dual Valve Catch Can | K&N Drop In | Power Stop Slotted and Drilled Rotors with Stock PP Pads | H&R Springs  | Curva Concept C7's | Continental DWS06 Extreme Contact Rubber |

"The Fukus" 2013 Focus ST | AJPTurbo Flex Fuel Tune | Megan Racing Catless Downpipe | Boomba BOV | FSWerks Short Shifter | Power Stop Brakes | Continental DWS06 Extreme Contact Rubber |

Offline FiveLeeter918

  • Ortiz Performance - Technical Sales
  • Vendor
  • Sr. Member
  • *
  • Tulsa, OK
  • Thank You
  • -Given: 19
  • -Received: 253
  • Posts: 292
  • Bewsted SHO
    • Ortiz Tuning and Performance
Re: FMIC Install/Routing
« Reply #2 on: June 29, 2020, 12:25:32 PM »
yeah buddy! ready to see track times.
- Lee
Technical Sales, Ortiz Tuning and Performance
F-150, Mustang, Lincoln MKS, Taurus SHO and Ford Flex Tuning

Ortiz Performance Vendor Forum | Find us on Facebook! | Shop Today!

Offline GotGrip?

  • The work around guy
  • Jr. Member
  • *
  • Minnesota
  • Thank You
  • -Given: 7
  • -Received: 13
  • Posts: 17
  • The Dude
Re: FMIC Install/Routing
« Reply #3 on: June 29, 2020, 12:26:12 PM »
Yep, AC condenser is just pushed back into the core support and bolted to core support.
2016 SHO Non-PP, GH/AJP E30 Tune,3Bar MAP, K&N Typoon, EPP Noisemaker Delete, MSD Coils, Catch Can, H&R Springs, ZEDD SL5 19x9.5, PS Drilled/Slotted rotors, FMIC Intercooler, SSM Trans Mounts, TCE Custom Catted DPs.

Current Dyno: 421/503 (pre-dp)

Upcoming -  Intercooler Sprayer, XDI35

Offline SM105K

  • IG @egocheckersho
  • Forum Supporters
  • Elite Member
  • *
  • *
  • Arizona
  • Thank You
  • -Given: 943
  • -Received: 1105
  • Posts: 1235
  • Thee Forum Cowboy
Re: FMIC Install/Routing
« Reply #4 on: June 29, 2020, 12:39:15 PM »
Yep, AC condenser is just pushed back into the core support and bolted to core support.

I should have been more clear in my question.  Does the AC perform normal because the front mount is blocking most of the condenser. 
"M" 2013 SHO PP | AJPTurbo E30 Tune | GH Intercooler | PPE Downpipes | Custom Magnaflow Resonator | 3rd Cat Delete | Dicunzolo Gen2 Trans Mounts| EPP Noisemaker Eliminator | MSD Coil Over Plugs | SP-542's | UPR Dual Valve Catch Can | K&N Drop In | Power Stop Slotted and Drilled Rotors with Stock PP Pads | H&R Springs  | Curva Concept C7's | Continental DWS06 Extreme Contact Rubber |

"The Fukus" 2013 Focus ST | AJPTurbo Flex Fuel Tune | Megan Racing Catless Downpipe | Boomba BOV | FSWerks Short Shifter | Power Stop Brakes | Continental DWS06 Extreme Contact Rubber |

Offline GotGrip?

  • The work around guy
  • Jr. Member
  • *
  • Minnesota
  • Thank You
  • -Given: 7
  • -Received: 13
  • Posts: 17
  • The Dude
Re: FMIC Install/Routing
« Reply #5 on: June 29, 2020, 12:43:40 PM »
Yep, AC condenser is just pushed back into the core support and bolted to core support.

I should have been more clear in my question.  Does the AC perform normal because the front mount is blocking most of the condenser.

Oh yes, still blows ice cold, the only part that is really blocked by the front mount is the Trans cooler and a little bit of the top of the AC portion. The condenser(lower) gets most of the air flow from what I can tell from the lower grill. But from what I can see in the datalogs I have there is no difference in temp in coolant or trans temp, or the change is negligible.
2016 SHO Non-PP, GH/AJP E30 Tune,3Bar MAP, K&N Typoon, EPP Noisemaker Delete, MSD Coils, Catch Can, H&R Springs, ZEDD SL5 19x9.5, PS Drilled/Slotted rotors, FMIC Intercooler, SSM Trans Mounts, TCE Custom Catted DPs.

Current Dyno: 421/503 (pre-dp)

Upcoming -  Intercooler Sprayer, XDI35

Offline SM105K

  • IG @egocheckersho
  • Forum Supporters
  • Elite Member
  • *
  • *
  • Arizona
  • Thank You
  • -Given: 943
  • -Received: 1105
  • Posts: 1235
  • Thee Forum Cowboy
Re: FMIC Install/Routing
« Reply #6 on: June 29, 2020, 01:42:54 PM »
Yep, AC condenser is just pushed back into the core support and bolted to core support.

I should have been more clear in my question.  Does the AC perform normal because the front mount is blocking most of the condenser.

Oh yes, still blows ice cold, the only part that is really blocked by the front mount is the Trans cooler and a little bit of the top of the AC portion. The condenser(lower) gets most of the air flow from what I can tell from the lower grill. But from what I can see in the datalogs I have there is no difference in temp in coolant or trans temp, or the change is negligible.

Cool cool, thanks buddy.
"M" 2013 SHO PP | AJPTurbo E30 Tune | GH Intercooler | PPE Downpipes | Custom Magnaflow Resonator | 3rd Cat Delete | Dicunzolo Gen2 Trans Mounts| EPP Noisemaker Eliminator | MSD Coil Over Plugs | SP-542's | UPR Dual Valve Catch Can | K&N Drop In | Power Stop Slotted and Drilled Rotors with Stock PP Pads | H&R Springs  | Curva Concept C7's | Continental DWS06 Extreme Contact Rubber |

"The Fukus" 2013 Focus ST | AJPTurbo Flex Fuel Tune | Megan Racing Catless Downpipe | Boomba BOV | FSWerks Short Shifter | Power Stop Brakes | Continental DWS06 Extreme Contact Rubber |

Offline GotGrip?

  • The work around guy
  • Jr. Member
  • *
  • Minnesota
  • Thank You
  • -Given: 7
  • -Received: 13
  • Posts: 17
  • The Dude
Re: FMIC Install/Routing
« Reply #7 on: June 29, 2020, 02:22:46 PM »
Fixed the pictures so they can actually be blown up. So feel free to check them out again!
2016 SHO Non-PP, GH/AJP E30 Tune,3Bar MAP, K&N Typoon, EPP Noisemaker Delete, MSD Coils, Catch Can, H&R Springs, ZEDD SL5 19x9.5, PS Drilled/Slotted rotors, FMIC Intercooler, SSM Trans Mounts, TCE Custom Catted DPs.

Current Dyno: 421/503 (pre-dp)

Upcoming -  Intercooler Sprayer, XDI35

 


Back to top
SimplePortal 2.3.5 © 2008-2012, SimplePortal