Ecoboost Performance Forum

Racing Department => Dyno Results => Topic started by: SHOdded on February 13, 2014, 03:20:22 AM

Title: Dyno Results
Post by: SHOdded on February 13, 2014, 03:20:22 AM
This thread is intended as a repository of dyno results for EB vehicles.  If you wish to post in here, please ONLY post dyno graphs/charts/videos, along with your vehicle type & mods at the time of the dyno.  As your signature may change over time, it is important to note this information in the post, even if it seems repetitive at the time.  Thank you!
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 03:27:54 AM
 Livernois Motorsports EcoBoost Flex on the Dyno
#1
12-12-2011, 12:58 PM

Note:  Based on the SCT device

Available in 4 stages. All stages included with purchase.

Modifications Include:

    Raised Boost
    Dyno Proven Air/Fuel Adjustments
    Altered Ignition Timing
    Removed Top Speed Limiter
    Torque Management Reduced or Removed
    Modified Shift Points/Firmness


Available for 91 or 93 Octane Fuel

Livernois Motorsports EcoBoost Flex on the AWD Dyno (http://www.youtube.com/watch?v=NZ8SA8ELvDw#ws)

Ed:  31 second mark – dyno graph

Not bad for our stage 2 tune only...

Peak gains were 43 WHP / 64 WTQ

It did however pick up much more in certain areas of the graph and feels 100% different!

Though we didn't put it on the dyno, we put our stage 4 tune in it at the track and it ran 13.3 @ 103 mph with only the tune and no other mods.

Thank you

Regards,

Rick LeBlanc
Livernois Motorsports

Last edited by Livernois Motorsports; 12-14-2011, 12:03 PM. Reason: typo on mph
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 03:44:27 AM
Scrming's Flex Dyno results Pt 1

Dyno Results!
#1
01-04-2012, 06:32 PM
Made the trek down to see Rick and the rest of the guys at Livernois today to put the Flex on their AWD dyno. After changing the stock mufflers out (and seeing just how restrictive they appeared to be!) I was curious... and since the tracks are closed I thought I would try the dyno. So here are the results...

First up was just the STOCK TUNE with 93 in the the tank. Unfortunately I didn't have a good baseline! ARGH! However Rick was KIND enough to overlay my results with THEIR baseline from their Flex, also stock tune and 93 octane. (Did I mention the GREAT customer service Rick provides!) So this is my Flex vs LMS Flex, with the only difference being my new MRT axle-back exhaust. NOW, understand these are different vehicles, different days, same dyno. These number are not meant to be 100% accurate and I'm not going to make any claims regarding gains! I will let everyone make their own mind up! LOL!!!

Here are the HP & Torque graphs:
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_1_42_08.jpeg)(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_1_42_25.jpeg)

AGAIN, I am not making any claims on the gains from the MRT system... but I did also notice my 0-60 MPH time drop quite a bit (stock tune) so between the dyno and the 0-60 MPH test, I have to believe the MRT exhaust is MORE than just Noise Fluff!!!

After a few pulls, Rick loaded my Stage 4+ Tune into the Flex... UNFORTUNATELY I was out of time (had to pick the kiddos up!), so we could not give the Flex a PROPER cool down! ARGH! STILL, the LOW END TORQUE gain was simply staggering!!!

Stock Tune vs LMS Stage 4+ Tune:
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_1_42_43.jpeg)

Rick got a the Flex on video!

John's EcoBoost Flex on the Dyno & Track (http://www.youtube.com/watch?v=WtQMmUMWuKY#ws)

Ed:  32 second mark – dyno graph

Thanks again to Rick and the staff at LMS!
Last edited by Scrming; 01-04-2012, 06:37 PM.
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 04:04:55 AM
Scrming's Flex Dyno results Pt 2

Alky Controls - Part 2
#1
03-16-2012, 07:50 PM
(OH CRAP... SHOULD BE PART 2!!! D'oah!!)

So spent the day at Livernois getting an updated tune for the methanol! Here are the dyno results!

Stock tune - 300 WHP / 307 WTQ
LMS Stage 4+ - 325 WHP / 360 WTQ
LMS Stage 4+ & Methanol - 359 WHP / 397 WTQ

So at the crank with the 4+ and methanol we are looking at about 450 HP and close to 500 ft/lbs!!! Now to hit the track!!

And the sheet:
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_03_28.jpeg)

BIG THANKS TO RICK AND DAN AT LMS!!!
Last edited by Showgun; 03-17-2012, 06:40 AM.
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 04:15:54 AM
Off topic.. Livernois First to Market with 6.2L Raptor Cams
#1
01-20-2012, 05:48 PM

Ed:  Topic abbreviated due to original posting's substantial pictorial content.  I will try to post these in a separate Livernois-related area.

Baseline dyno numbers were 336 RWHP / 359 RWTQ
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_13_55.jpeg)

In addition to the cams, we also added an Airaid CAI Stainless Works Longtube Headers, Mid-Pipe w/ Cats, and Catback.
The last few trucks with the exact mods (minus cams) made right around 370 RWHP / 395 RWTQ
The post mod numbers with cams, full SW exhaust, CAI and tune were 405 RWHP / 410 RWTQ.
Peak gains were 35 RWHP / 10 RWTQ, but up top the gains were much more.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_14_27.jpeg)

Livernois Motorsports 405 RWHP Cammed 6.2L Ford Raptor - First Set of Aftermarket Cams Available (http://www.youtube.com/watch?v=rsTJwzrw-pU#ws)

Ed:  1:42 mark - dyno graphs
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 04:23:02 AM
Livernois Motorsports Tuned EcoBoost F150 on the Dyno/Street
#1
03-02-2012, 12:03 PM
We are waiting on tuners to arrive and still working daily on the dyno and street testing drivability and datalogging with our truck.

We will offer multiple stages and fuel options, plus towing tunes.

Attached is a graph from the baseline and one of the best pulls so far. Both the baseline and tuned file were done with 93 octane fuel.

It comes into boost quick now, so there is a spike at the beginning of the graph. Peak gains on this pull were 69 RWHP and 88 RWTQ. Notice though up top, gains are much more. I left the cursor on the graph so you can see the gains. Around 104 RWHP / 114 RWTQ.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_22_05.jpeg)
Livernois Motorsports Tuned (93 Octane) EcoBoost F150 on the Dyno & Street (http://www.youtube.com/watch?v=GKMJqjkmXng#ws)

Ed:  0:36 mark - dyno graph

Thank you

Regards,

Rick LeBlanc
Livernois Motorsports
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 04:31:37 AM
Livernois Motorsports EcoBoost Tuning
#1
12-12-2011, 01:23 PM
All of our tunes have been developed in-house on our AWD chassis dyno or the track and proven on the street using our Taurus SHO and EcoBoost Flex shop vehicles.

To my knowledge, we've tuned more EcoBoost vehicles than anyone in the country (over 250) and have had zero failures. We also claim the world's quickest Gen IV SHO, a customer's vehicle which runs 12.13 @ 117 mph. Our SHO with only our custom tune and Corsa exhaust has been a best of 12.69 @ 107 mph and our Flex with only our custom tune has been a best of 13.3 @ 103 mph.

Our SHO on the AWD dyno
Livernois Motorsports 2010 Taurus SHO on the Dyno (http://www.youtube.com/watch?v=_ktu3X_WpYU#ws)

Ed:  0:47 mark - dyno graph

Available in 4 stages. All stages included with purchase.

Modifications Include:

    Raised Boost
    Dyno Proven Air/Fuel Adjustments
    Altered Ignition Timing
    Removed Top Speed Limiter
    Torque Management Reduced or Removed
    Modified Shift Points/Firmness

Available for 91 or 93 Octane Fuel

Thank you

Regards,

Rick LeBlanc
Livernois Motorsports
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 04:42:34 AM
Dyno Results 3-27-2012 EcoBrick Bob
#1
03-27-2012, 11:44 AM
Did 7 Pulls today @ Gulf Coast Motorsports. Their dyno is a Dynojet 424xLC Linx, which I believe is the same model that is at Livernois. Justin Daniels who did the runs said it is one of about 15 in the world like it. It was a beautiful morning. Temp ranged from 74.5 to 77.2 Deg. F. HG 29.50-29.52 Humidity 40% to 42% Runs were completed between 9:48 & 10:49 AM.
Here are the Max Power & Max Torque numbers
-----------------------------Max Power----------Max Torque
Pull #1 Torrie Tune #116 354.93++++++++402.22
Pull #2 Torrie Tune #114 366.33++++++++409.44
Pull #3 Torrie Tune #115 369.44++++++++406.59
Pull #4 Torrie Tune #113 354.54++++++++391.12
Pull #5 Shifted down - deleted
Pull #6 Torrie Stock Tune (3 bar sensor) Deleted as we accidentally left W/M on... Interestingly we lost quite a bit of power and torque. As I remember Max Power was around 273 and Max torque was around 300.
Pull #7 Torrie Stock Tune 294.46++++++++332.86 Note: this tune is the same as the above ones & uses a 3 bar sensor, but has stock A/F & Boost values in the tune. A/F was a straight line & max boost was 13.10.

Assuming that my AWD system wastes 20% of the engine power & Torque, My Max Power would be around 460 & Max Torque 510.

Not too shabby for e-mail tuning!!!!

THANKS!!!!!! TORRIE @ UNLEASHED TUNING
Last edited by EcoBrick Bob; 03-31-2012, 03:59 PM.

Here are a few graphs of my Dyno Pulls.

First.... Stock A/F & Boost (3 Bar sensor version)
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_38_17.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/EcobrickBob%20Dyno1%2020120327_1_zpsyx0xlaoa.jpg)
This is the same stock tune but with W/M spraying. Note how much the spray hurts the numbers when it isn't tuned for W/M.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_38_35.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/EcobrickBob%20Dyno2%2020120327_1_zpsv63zhdsk.jpg)
Torrie's printout of the two best runs, overlapping.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_38_51.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/EcobrickBob%20Dyno3%2020120327_1_zpshwii4t1c.jpg)
The best run overall... with the highest performance. Note how everything peaks in the 5,000 RPM range.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_39_25.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/EcobrickBob%20Dyno4%2020120327_1_zpsgpagsbvh.jpg)
I will post the actual paper printout I received from Gulf Coast Motorworks, with a boost graph sometime tomorrow. Usable boost peaked at 17.72 on this run.

Here is the paper printout of the 115 Torrie Tune.

Note the Power Scale is 0-400 and the Torque Scale is 0-500. The peak boost of over 22 occurred when the blow off valve opened when the Dyno Pull ended.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_2_39_25.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/EcobrickBob%20Dyno5%2020120327_1_zpsz8uqkimj.jpg)
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 05:01:26 AM
LMS - Stage 2 & 4+ vs Stock - Dyno Results
06-01-2012, 10:41 AM

Here is a SHO stock vs. 4+. This car baselined high in my opinion. But it was the same car the same day.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_3_00_20.jpeg)

The stage 2&3 graphs will look the same.

Here is a graph showing stage 2 compared to stock. Ignore the spike in the beginning of the graph. Blue is stock, red is tuned.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_3_00_43.jpeg)

-Rick
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 05:04:29 AM
Livernois Motorsports 2013 SHO, MKS, Flex Tuner Now Shipping!
#1
08-31-2012, 10:58 AM
Our 2013 SHO was baselined at Milan Dragway in 70 degree heat and ran 14.3 @ 96 mph. A few weeks later, with only our custom tune and no other modifications, the car ran 13.4 @ 103 mph in 102 degree heat.

See the dyno video below
Livernois Motorsports - First to Tune 2013 Taurus SHO (http://www.youtube.com/watch?v=VnXVzV4gmDI#ws)

Ed:  0:36 mark – dyno graph

Thank you

Regards,

Rick LeBlanc
Livernois Motorsports
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 05:16:51 AM
Crash712us's SHO on the dyno

09-06-2012, 08:37 AM
Ok here is my dyno graph comparing the +4 meth sct tune to the new stage 5 Mycal meth tune.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_3_15_13.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/crash712us%20Dyno%2020120906_zpsfmvzyxwn.jpg)
Ambient Temps in mid to high 80s.
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 05:19:02 AM
FirstSHO Dyno Results
09-06-2012, 07:38 PM

(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_3_15_44.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/First-SHO%20Dyno%2020120906_zpssttbxise.jpg)
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 05:30:13 AM
bpd1151 Dyno Results MyCal Stage 5 tune
10-27-2012, 06:53 PM

Here's my dyno sheet, as presented by Rick @ LMS, immediately following delivery of my SHO after Dan Millen got done working his magic on it, by applying the newest "Stage 5" tune file, in conjunction with the new AIW MyCalibrator Device.

The Blue is a dyno of a stock SHO with factory tune, Red is mine as of 10/26/12.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_3_29_31.jpeg)

http://www.ecoboostperformanceforum.com/index.php?topic=467.msg2350#msg2350 (http://www.ecoboostperformanceforum.com/index.php?topic=467.msg2350#msg2350)

2010 SHO, Meth Kit, Offroad downpipe, NESHO Exhaust, Hood Vents, Airaid CAI
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 05:43:51 AM
Unleashed - 2013 Focus ST - Dyno Results
09-26-2012, 02:20 PM
Stock run data below 87 Octane. Note how Engine coolant temperature plays a massive role in end power output once you get to real world temperatures. Also note that Cat over temp is also to blame for the upper RPM power reduction.

Runfile 012 @ 145 degrees ECT
Runfile 013 @ 185 degrees ECT
Runfile 014 @ 196 degrees ECT

As temperatures increase COT kicks in and timing decreases.
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_3_42_34.jpeg)

Scrming
10-02-2012, 06:04 PM
No rumor about it!!!
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_3_43_02.jpeg)

tmcphail
10-16-2012, 08:55 PM
We had the first Custom Tuned Focus ST on the planet to begin, then first to market with SCT custom tuning for our customers.

So I figured I would kick things up a notch with this graph :
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_3_45_13.jpeg)

Dyno :

SCT vs Stock Calibration Notes:

Same SCT calibration was tested on both 87 and 93....power is down about 15fwhp on 87 vs 93.

NOTE: SCT recommends 93 or 91 octane.

The big deal is the power gain when the car is "hot" and at normal drive temp (99% of your time)

Stock Boost Levels- Stock the ST will make spikes of boost around
21.5 psi and then holds between 20psi - 17psi, depending on the commanded torque.

SCT Calibration Boost Levels - SCT 93 Octane Calibration the ST will make spikes of boost around 23.5 psi and then holds between 22.5psi
- 17psi, depending on the commanded torque.

Air Inlet Temps are very good.....after 10 minutes of idle time and
7 runs in a row they climbed from 80F (run 1) to 110F (run 7).

Stock Speed Limit is 186mph

Stock Rev Limit is 6700rpm
SCT Calibration Rev Limit is 7300rpm

Torque Truncation has been eliminated
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 11:56:26 AM
steve142857 Dyno camparison stock vs stg 2-3-4-5
#1
11-09-2012, 11:57 AM
I went to Dynodoc yesterday in Montreal for a little dyno session to compare after a year and a half since last dyno session with that same guy. I also had my car dynoed in Detroit, but they use a different dyno, which, according to Dynodoc guy, is reading a bit more power than his dynopack. Instead of putting the car on rolls like at Livernois, the dynajet requires that you remove the wheels and you plug a machine to each wheel.

When I went to Detroit, I was dynoed, when it was almost 100F outside at 380hp/400lbs with stage 4+. Now everyone that upgraded with mycal and stage 5 agrees to say that there is a noticeable difference between 4+ and 5, so I would have expected my dyno numbers to be a bit higher... But I am happy with them anyways.

Thanks and here are the graphs (first is May 2011 with stock, stage 2-3 and stage 4(2 runs of stage 4)); (second graph is the one of yesterday with stage 5). Note that in May 2011, my car was bone stock except for tuning and H&R... Since then, it has Airaid intake, custom exhaust and methanol injection:

(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_9_55_06.jpeg)(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_9_55_31.jpeg)
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 12:05:41 PM
Darreli's Dyno Sheet
#1
12-13-2012, 12:55 PM
Darrell's 2010 SHO has the following mods:
The factory turbo housing was modified and it was fitted with a larger billet wheel.

Before numbers were 277 WHP / 371 WTQ after numbers were 435 WHP / 521 WTQ. (If you get rid of the initial spike in the baseline, it made 330 WTQ stock)
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_10_01_59.jpeg)

Looks at the gains... it's up 190 WHP / 225 WTQ at 6,250 (stock vs all mods)

Here is before turbos and downpipe vs all current mods
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_10_02_19.jpeg)

Darrell and Mike both have the power to go 11's, they just need to get the power to the ground.

Thanks for looking!

-Rick
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 12:26:33 PM
bpd1151 Video of my dyno & 12.37 run, compliments of Livernois Motorsports!
#1
11-25-2012, 02:51 PM
Thanks to Mr. Rick LeBlanc of Livernois Motorsports fame, for putting this short video clip of my most recent dyno pull, and 12.37 run down the Milan, MI dragway during their 2nd, 2012 Customer Appreciation Day.  The hospitality, professionalism, and ability to apply their talents in making my 2010 SHO go ever faster is truly much appreciated.  Thanks to all the staff at LMS for another wonderful experience. Enjoy the video folks

http://youtu.be/ohewGN6MVwU (http://youtu.be/ohewGN6MVwU)

Ed:  1:06 mark - Dyno graph
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 12:31:17 PM
Scrming Dyno with Livernois tune +/- Methanol
06-08-2012, 12:02 PM
Ok... realize this is a Flex EcoBoost... But this should give you an idea of the gains you can realize with a tune...

BLUE - Stock Tune
RED - Livernois Stage 4+ Tune
GREEN - Livernois Stage 4+ plus Methanol Tune
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_10_30_46.jpeg)

The low end torque improvement is simply STUNNING!!!
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 12:37:46 PM
For the V fanatics at heart ;)
LMS Black Diamond Caddy V Coupe... Head/Cam Build w/ Photos and Dyno Sheet
#1
02-28-2012, 11:06 AM
We recently did a build for a customer with an 700 mile auto trans Black Diamond Coupe.

In stock form, it made 438 RWHP / 431 RWTQ. After the following mods, it made 661 RWHP / 605 RWTQ.

Mods are:

Livernois Motorsports CNC LSA Cylinder Heads / Livernois Motorsports Stage 2C High Lift Camshaft / Livernois Motorsports Pro-Series Heat Exchanger / Livernois Motorsports 2.55" Supercharger Pulley / Livernois Motorsports Double Bearing Idler Pulley / Livernois Motorsports Hardened Pushrods / Innovators West 9.1" Oversize Balancer / Oversize Crank Pulley Ring / Kooks Stainless Longtube Headers / Kooks Stainless Connection Pipe w/ Cats / Solid Supercharger Coupler / Airaid Cold Air Intake / 60# Injectors / NGK TR6 Spark Plugs / 160 Degree Thermostat / GM Supercharger Discharge to Intercooler Gasket / Billet 10.5" Stall Converter / ARP Head Studs / GM Head Gaskets / GM Exhaust Gaskets / NGK Spark Plugs / Eibach Springs / Mickey Thompson 305/35/19 Drag Radials / Livernois Motorsports Dyno Tune / Tint... So dark it looks sprayed on, including windshield
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_10_36_23.jpeg)

2012 Black Diamond Head/Cam CTS-V Coupe - 661 RWHP! (http://www.youtube.com/watch?v=6paMzbgHIGI#ws)

Ed:  1:15 mark - Dyno graph

Regards,

Rick LeBlanc
Livernois Motorsports
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 12:51:34 PM
First-SHO Dyno results 6/12/13
#1
06-13-2013, 02:50 PM
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_10_49_53.jpeg)(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_10_50_21.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/First-SHO%20Dyno%2020130613_zpssx0bre9x.jpg)
Nice improvement!


FASTEST 2011 Ford Taurus SHO on record @ 12.0909 115 mph
Silver/Black LOADED / Ford Lockpick / Forgestar F14"s 20x9.5 with Nitto Invo's / Wilwood Front Big Brake Kit from TCE
Airaid CAI / Corsa Cat back / Livernois Down Pipes / Livernois Tune's / H&R Springs with camber bolts.
Torrie - 170 F Thermo & Radiator / L&M Airflow Throttle Body "Only one made and I have it" / Alkycontrol Meth Injection
Upgraded Turbo's / 2013 Trans and Oil Cooler / LED's on always

06-13-2013, 06:33 PM
OK OK, boost is around 20-22 psi I will tell you this program will not be for a stock suspension as the numbers power up very quick for the track.

My car has gotten better MPG with a program. All of them as more torque moves the vehicle quicker.

The throttle body is a one only make and I really do not know what gain it makes as the numbers are close to other cars, but throttle response is improved with it.
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 12:58:30 PM
gregoire Dyno chart from Livernois visit
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_10_56_50.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/gregoire%20Dyno%2020130223_zpspzwd4si7.jpg)
2013 PP Downpipes, exhaust, CAI, Springs, 170 degree thermo and tune.
Last edited by gregoire; 02-23-2013, 05:09 PM.
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 01:05:36 PM
OnlyA6 Dyno Results - 2013 SHO - 397 WHP
#1
04-20-2013, 05:23 PM
397 AWHP / 381 AWTQ

2013 Taurus SHO / Performance Package / Livernois Motorsports 93 Tune / NGK 1 step colder plugs
170* Thermostat / AIRAID Intake / Corsa Exhaust

4th Gear pulls, SAE corrected on a Dynocom Dyno
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_11_04_42.jpeg)
(http://i1315.photobucket.com/albums/t597/PerfA_ZN0W/2010-up/Dyno%20Sheets/OnlyA6%20Dyno%2020130420_zpsyvwe50hx.jpg)
Dyno sheet shows the 1st and 3rd pull. 1st pull engine was still fairly cold. The HP seemed high - I was expecting somewhere around 350. For comparison, right after me a 2011 Camaro SS L99 Auto w/ intake made 333 WHP / 346 WTQ, which is right on for that car. So who knows...

Last edited by ONLYA6; 04-20-2013, 05:38 PM.
Title: Re: Dyno Results
Post by: SHOdded on February 13, 2014, 01:17:50 PM
Scrming MRT catback installed on Flex
07-21-2012, 08:06 PM
Not sure if the SHO uses the same mufflers as the Flex.. but we cut open the stock mufflers from our Flex and found them very restrictive.

Now, unfortunately we didn't do a true before and after dyno session... but we did compare my Flex with the new exhaust against Livernois stock baseline dyno... so not an ideal situation, but i think it does confirm there is some HP to be freed up in the exhaust:

RED = Stock Base Line
BLUE = MRT axle back

HP (fig 1), Torque (fig 2)
(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_11_16_40.jpeg)(http://www.ecoboostperformanceforum.com/gallery/60_13_02_14_11_17_09.jpeg)
Title: Re: Dyno Results
Post by: SHOdded on February 15, 2014, 11:14:41 PM
twnscrw13 Whoop.. new mods. :)

http://www.ecoboostperformanceforum.com/index.php?topic=1261.msg13874#msg13874 (http://www.ecoboostperformanceforum.com/index.php?topic=1261.msg13874#msg13874)

2013 PP SHO. LMS 4+ tune, catted down pipes, Corsa Exhaust, AirRaid CAI, truck plugs, 170 thermostat
Title: Re: Dyno Results
Post by: SHOdded on February 15, 2014, 11:15:28 PM
Courier6 Re: Whoop.. new mods. :)

http://www.ecoboostperformanceforum.com/index.php?topic=1261.msg13936#msg13936 (http://www.ecoboostperformanceforum.com/index.php?topic=1261.msg13936#msg13936)

2013 PP SHO.  LMS tune, PPE downpipes, Corsa catback, Air Raid CAI, 170 deg thermostat

0:23 mark – Dyno graph
Title: Re: Dyno Results
Post by: SHOdded on February 15, 2014, 11:16:24 PM
4DRHTRD Baseline pull in my V

http://www.ecoboostperformanceforum.com/index.php?topic=1629.msg20139#msg20139 (http://www.ecoboostperformanceforum.com/index.php?topic=1629.msg20139#msg20139)

Baseline pull 2011 CTS-V Coupe 509HP on 91 octane (http://www.youtube.com/watch?v=hy5TSdFG6dc#ws)

0:33 mark – Dyno graph
Title: Re: Dyno Results
Post by: SHOdded on February 15, 2014, 11:17:08 PM
4DRHTRD First Ecoboost to hit 600WHP!

http://www.ecoboostperformanceforum.com/index.php?topic=1172.msg12675#msg12675 (http://www.ecoboostperformanceforum.com/index.php?topic=1172.msg12675#msg12675)

http://www.ecoboostperformanceforum.com/index.php?topic=1172.msg12711#msg12711 (http://www.ecoboostperformanceforum.com/index.php?topic=1172.msg12711#msg12711)

0:37 mark – Dyno graph

2011 Ford Flex Tuxedo Black Titanium EB
Megan Coilovers, Custom fuel system, E85, custom cutout
Title: Re: Dyno Results
Post by: SHOdded on February 15, 2014, 11:18:11 PM
DJE624  LMS Tuned Stock, 4 and 4+

http://www.ecoboostperformanceforum.com/index.php?topic=1324.msg15070#msg15070 (http://www.ecoboostperformanceforum.com/index.php?topic=1324.msg15070#msg15070)

https://www.youtube.com/watch?v=v8kJDDzZfHg (https://www.youtube.com/watch?v=v8kJDDzZfHg)

2012 SHO
Title: Re: Dyno Results
Post by: SHOdded on February 15, 2014, 11:23:56 PM
Shoman04 LMS Tuned with Meth

(http://www.ecoboostperformanceforum.com/gallery/60_15_02_14_9_23_31.jpeg)

See the video at:  https://www.youtube.com/watch?v=hCIWVhlcYQk (https://www.youtube.com/watch?v=hCIWVhlcYQk)
See the dyno graph at:  https://www.youtube.com/watch?v=pU8rfm6OHbQ (https://www.youtube.com/watch?v=pU8rfm6OHbQ)

2011 SHO, Livernois Tune Stage 5, Airaid CAI, Dynomax Mufflers, LMS down-pipe, Magnaflow X-pipe, Custom 2.5"exhaust pipe
Title: Re: Dyno Results
Post by: SHOdded on February 15, 2014, 11:25:02 PM
CooperS7777 Dyno with 87 Octane

http://www.ecoboostperformanceforum.com/index.php?topic=815.msg12107#msg12107 (http://www.ecoboostperformanceforum.com/index.php?topic=815.msg12107#msg12107)

14' Ex Sport, 402a package, tow package
Title: Re: Dyno Results
Post by: SHOdded on February 16, 2014, 11:02:14 AM
K&N's claimed gains for stock 2011 SHO

http://www.ecoboostperformanceforum.com/index.php?topic=1700.msg21804#msg21804 (http://www.ecoboostperformanceforum.com/index.php?topic=1700.msg21804#msg21804)
Title: Re: Dyno Results
Post by: SHOdded on February 16, 2014, 07:31:52 PM
BiGMaC's Dyno for PPE down pipes Based on Stock Tune

Dyno of stock vs catless
Dyno of catted vs catless

http://www.ecoboostperformanceforum.com/index.php?topic=2054.msg28342#msg28342 (http://www.ecoboostperformanceforum.com/index.php?topic=2054.msg28342#msg28342)

2013 SHO, No tunes loaded
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 12:05:24 AM
Livernois Motorsports now offers tuning for 2013+ Fusion 2.0L EcoBoost

http://www.ecoboostperformanceforum.com/index.php?topic=777.msg7221#msg7221 (http://www.ecoboostperformanceforum.com/index.php?topic=777.msg7221#msg7221)
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 05:34:25 AM
CooperS7777  2014 Explorer Sport (Stock) Baseline

http://www.ecoboostperformanceforum.com/index.php?topic=1183.msg12818#msg12818 (http://www.ecoboostperformanceforum.com/index.php?topic=1183.msg12818#msg12818)
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 05:35:35 AM
4DRHTRD  Downpipes for Flex/SHO/Explorer V6 Ecoboost/Lincoln MKT/MKS

http://www.ecoboostperformanceforum.com/index.php?topic=310.msg1043#msg1043 (http://www.ecoboostperformanceforum.com/index.php?topic=310.msg1043#msg1043)

These dyno runs compare the stock downpipes and exhaust with the cutout functioning like in the video VS the PPE downpipes and stock exhaust, no cutout.

Ford Flex with exhaust cutout (http://www.youtube.com/watch?v=48WlWGK2o9E#)
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 05:36:10 AM
Airaid Dyno on Ecoboost F150 by Dragzine

http://cdn.speednik.com/files/2012/04/163.jpg (http://cdn.speednik.com/files/2012/04/163.jpg)
http://www.dragzine.com/tech-stories/engine/airaid-delivers-fast-quick-bolt-on-power-for-2011-ecoboost-f-150/ (http://www.dragzine.com/tech-stories/engine/airaid-delivers-fast-quick-bolt-on-power-for-2011-ecoboost-f-150/)
QuoteBaseline testing yields 298.43 horsepower and 319.15 ft/lbs of torque at the axles. With AIRAID, our Ecoboost F-150 turns in peak numbers of 306.59 horsepower (8.16 horses) and 328.06 ft/lbs of torque (8.91 ft/lb) on our in-house Dynojet. Though we have to note that under the curve, there were gains of 30+ horsepower 28+ ft/lbs.
(http://cdn.speednik.com/files/2012/04/163.jpg)
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 05:49:45 AM
AFE Stage 2 Pro CAI for 2012-2014 EB F150

http://morepowertuning.com/images/54-12192_Dyno.jpg (http://morepowertuning.com/images/54-12192_Dyno.jpg)

(http://www.ecoboostperformanceforum.com/gallery/60_17_02_14_3_49_17.jpeg)
(http://morepowertuning.com/images/54-12192_Dyno.jpg)
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 06:04:28 AM
An interesting comparo on filter airflow (stock vs K&N vs Green Filter).  Haven't found any dyno data yet, sadly.

Green Filters USA - High Performance Filter - Focus ST (http://www.youtube.com/watch?v=6AOygXeyp7o#)
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 06:58:00 AM
4DRHTRD Turbo Tech / Dyno on ATP ugpraded turbo for transverse V6

http://www.ecoboostperformanceforum.com/index.php?topic=1167.msg12599#msg12599 (http://www.ecoboostperformanceforum.com/index.php?topic=1167.msg12599#msg12599)

Ford Flex Ecoboost on upgraded turbos 505HP/515TQ
Ford Flex Ecoboost on upgraded turbos 505HP/515TQ (http://www.youtube.com/watch?v=W-DGoA-COYM#ws)
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 07:08:02 AM
4DRHTRD  New timeslips and dyno from ATP for Garrett turbos on F150

http://www.ecoboostperformanceforum.com/index.php?topic=1141.msg12256#msg12256 (http://www.ecoboostperformanceforum.com/index.php?topic=1141.msg12256#msg12256)

2011 F150 EB 4WD SuperCrew ATP +2 Turbos
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 07:14:58 AM
Livernois Motorsports 2013 Explorer Sport

http://www.ecoboostperformanceforum.com/index.php?topic=573.msg3756#msg3756 (http://www.ecoboostperformanceforum.com/index.php?topic=573.msg3756#msg3756)

Livernois Motorsports 2013 Explorer Sport (http://www.youtube.com/watch?v=LQrmz_mDWT8#ws)

Custom Tune Only
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 07:18:51 AM
Ryan327  2013Explorer Sport w/ Lund tune

http://www.ecoboostperformanceforum.com/index.php?topic=574.msg3788#msg3788 (http://www.ecoboostperformanceforum.com/index.php?topic=574.msg3788#msg3788)

http://www.ecoboostperformanceforum.com/index.php?topic=574.msg4218#msg4218 (http://www.ecoboostperformanceforum.com/index.php?topic=574.msg4218#msg4218)

Watch:  VID_20130724_143953.mp4 (http://www.youtube.com/watch?v=a5XNT9QyBmc#ws)
Title: Re: Dyno Results
Post by: SHOdded on February 17, 2014, 11:55:02 PM
Unleashed Tuning 2013 Focus ST 2.0EB Stock vs SCT Tune

(http://www.fastpartsnetwork.com/images/fst1.jpg)
Title: Re: Dyno Results
Post by: SHOdded on February 20, 2014, 01:29:46 PM
4DRHTRD  Dyno done for upgraded stock turbos 459/521
http://www.ecoboostperformanceforum.com/index.php?topic=1104.msg11845#msg11845 (http://www.ecoboostperformanceforum.com/index.php?topic=1104.msg11845#msg11845)

2011 Flex, Stock turbos upgraded with a billet stock size compressor wheel


For comparison, darreli  2011 (?) SHO with LMS tune & upgraded turbos

http://www.ecoboostperformanceforum.com/index.php?topic=1104.msg11855#msg11855 (http://www.ecoboostperformanceforum.com/index.php?topic=1104.msg11855#msg11855)
Title: Re: Dyno Results
Post by: SHOdded on February 23, 2014, 06:08:43 PM
Unleashed Tuning 2014 Taurus SHO

http://www.ecoboostperformanceforum.com/index.php?topic=1996.msg27199#msg27199 (http://www.ecoboostperformanceforum.com/index.php?topic=1996.msg27199#msg27199)
Title: Re: Dyno Results
Post by: SHOdded on February 26, 2014, 06:09:55 PM
bpd1151 2010 Taurus SHO Dyno after adding ATP +2 Turbos

http://www.ecoboostperformanceforum.com/index.php?topic=2162.msg30637#msg30637 (http://www.ecoboostperformanceforum.com/index.php?topic=2162.msg30637#msg30637)
Dyno about 3:43 mark

Full Dyno graph:
http://www.ecoboostperformanceforum.com/index.php?topic=2162.msg30658#msg30658 (http://www.ecoboostperformanceforum.com/index.php?topic=2162.msg30658#msg30658)

Current list of mods always at:  http://www.hkmediachicago.com/sponsored-and-business-affiliates.html (http://www.hkmediachicago.com/sponsored-and-business-affiliates.html)

Title: Re: Dyno Results
Post by: SHOdded on March 02, 2014, 02:07:55 AM
painterpatt's 2011 Ford Flex "Egoboost"

http://www.ecoboostperformanceforum.com/index.php?topic=2175.msg31115#msg31115 (http://www.ecoboostperformanceforum.com/index.php?topic=2175.msg31115#msg31115)

Unleashed Tuning tune, Airaid Intake
Title: Re: Dyno Results
Post by: SHOdded on March 23, 2014, 10:28:29 PM
2.0L EB Fusion Tuning SCT X4 by Unleashed Tuning

http://www.ecoboostperformanceforum.com/index.php?topic=2407.msg35181#msg35181 (http://www.ecoboostperformanceforum.com/index.php?topic=2407.msg35181#msg35181)

(https://fbcdn-sphotos-c-a.akamaihd.net/hphotos-ak-prn1/t31.0-8/135272_626410120741545_186712946_o.jpg)

No mods, just the tune!
Title: Re: Dyno Results
Post by: SHOdded on April 04, 2014, 11:24:37 AM
Dave's 2012 SHO after latest LMS tune/dyno:

(http://i1059.photobucket.com/albums/t440/DJE624/RaceTune_zps33ae605c.jpg)

https://www.youtube.com/watch?v=g3P_4QMwAlQ (https://www.youtube.com/watch?v=g3P_4QMwAlQ)
Title: Re: Dyno Results
Post by: SHOdded on April 28, 2014, 11:22:55 PM
bigmoneycloser's 2014 XSport dyno results 4/28/2014:

http://www.ecoboostperformanceforum.com/index.php?topic=2747.msg41271#msg41271 (http://www.ecoboostperformanceforum.com/index.php?topic=2747.msg41271#msg41271)

LMS 93 high boost/AirAid CAI/170* thermostat/3 Bar Map Sensor/LMS-Corsa CatBack Exhaust/LMS Catted Downpipes
Title: Re: Dyno Results
Post by: SHOdded on May 04, 2014, 09:22:07 PM
MPT Tuned F150 - StrawHatShinobi

http://www.ecoboostperformanceforum.com/index.php?topic=2821.msg42010 (http://www.ecoboostperformanceforum.com/index.php?topic=2821.msg42010)

AFE stg2, FR CAC, Solo off road downs, 3" exhaust, Morkin THE56 turbos, meth injection, MPT 91 octane tune, Walbro 450 pump.  Meth was on for the run but tune is not a meth tune.
Title: Re: Dyno Results
Post by: SHOdded on May 13, 2014, 10:01:46 PM
LMS Tuned 2013 Taurus SHO - OnlyA6

Detuned, per customer request:
http://www.ecoboostperformanceforum.com/index.php/topic,2931.msg43771.html#msg43771 (http://www.ecoboostperformanceforum.com/index.php/topic,2931.msg43771.html#msg43771)
Max
http://www.ecoboostperformanceforum.com/index.php/topic,2931.msg43772.html#msg43772 (http://www.ecoboostperformanceforum.com/index.php/topic,2931.msg43772.html#msg43772)

2013 Taurus SHO:  Upgraded turbos with Garrett GTX billet compressor wheels and Turbosmart wastegates, PPE catted downpipes, Corsa catback, EBPP intercooler pipes w/ Turbosmart BOV, Livernois/Alky meth kit, 3 BAR map, Stock intake w/ K&N, SP534 plugs, 170* thermostat
Title: Re: Dyno Results
Post by: Silver14Ti on May 26, 2014, 09:01:26 PM
2014 Fusion Titanium FWD 2.0L EcoBoost - Livernois Motorsports 93 Octane Tune Only - 250 miles on the odometer

(http://i45.photobucket.com/albums/f81/saleenspeedster/rl_zpsdadc54c6.jpg) (http://s45.photobucket.com/user/saleenspeedster/media/rl_zpsdadc54c6.jpg.html)
Title: Re: Dyno Results
Post by: SHOdded on August 09, 2014, 11:32:23 AM
bpd1151's 2010 Taurus SHO after Livernois Motorsports Buildout 8/9/2014

World's highest horsepower EcoBoost Taurus SHO by Livernois Motorsports (http://www.youtube.com/watch?v=WSlvKcG3neo#ws)
(http://www.ecoboostperformanceforum.com/gallery/60_09_08_14_8_31_32.jpeg)

To Quote:

Pro-Series Longblock engine that includes:
Livernois Motorsports Proprietary fully coated Pistons
Livernois Motorsports Proprietary Billet Connecting Rods
Livernois Motorsports Proprietary Main Studs
Livernois Motorsports Proprietary Head studs
Livernois Motorsports Ported Cylinder heads
Title: Re: Dyno Results
Post by: ShoBoat on August 09, 2014, 03:52:34 PM
s*** 600WHP? That's really outstanding.
Title: Re: Dyno Results
Post by: SHOnUup on August 09, 2014, 06:44:50 PM
Quote from: ShoBoat on August 09, 2014, 03:52:34 PM
s*** 600WHP? That's really outstanding.
X2
Title: Re: Dyno Results
Post by: BiGMaC on August 09, 2014, 06:59:06 PM
Quote from: SHOnUup on August 09, 2014, 06:44:50 PM
Quote from: ShoBoat on August 09, 2014, 03:52:34 PM
s*** 600WHP? That's really outstanding.
X2
X3
Title: Re: Dyno Results
Post by: ecoboostsho on August 09, 2014, 07:07:01 PM
Wow...

Sent from my XT1060 using Tapatalk

Title: Re: Dyno Results
Post by: BiGMaC on August 09, 2014, 07:11:49 PM
Here's what the Wallace Racing Calculator says:
(http://i1331.photobucket.com/albums/w596/knot2bfound/Junk/BPDQuaterpossible_zps7b3a04ff.png) (http://s1331.photobucket.com/user/knot2bfound/media/Junk/BPDQuaterpossible_zps7b3a04ff.png.html)
Title: Re: Dyno Results
Post by: FoMoCoSHO on August 09, 2014, 10:31:50 PM
Quote from: BiGMaC on August 09, 2014, 06:59:06 PM
Quote from: SHOnUup on August 09, 2014, 06:44:50 PM
Quote from: ShoBoat on August 09, 2014, 03:52:34 PM
s*** 600WHP? That's really outstanding.
X2
X3
X4

So much win!
Title: Re: Dyno Results
Post by: BiGMaC on August 10, 2014, 02:14:07 AM
Quote from: BiGMaC on August 09, 2014, 07:11:49 PM
Here's what the Wallace Racing Calculator says:
(http://i1331.photobucket.com/albums/w596/knot2bfound/Junk/BPDQuaterpossible_zps7b3a04ff.png) (http://s1331.photobucket.com/user/knot2bfound/media/Junk/BPDQuaterpossible_zps7b3a04ff.png.html)

It occurs that the calculator may use CHP... in which event Mike could have a 10 second SHO... here's the numbers with 20% added....
computed from your vehicle weight of 4250 pounds and HP of 740 is 10.43 seconds and MPH of 129.56 MPH.
Title: Re: Dyno Results
Post by: SHOdded on August 15, 2014, 11:32:40 PM
scap99's 2013 FX4 Tuned by Leading Edge Tuning 8/15/2014

(http://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=3524.0;attach=4396)
(http://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=3524.0;attach=4403)

To Quote:

Downpipes, meth, intake, intercooler, and upgraded in-tank fuel pump.
Tune is the E40 performance tune from LET.
Title: Re: Dyno Results
Post by: SHOdded on September 14, 2014, 08:11:20 PM
Fordman77's 2.0l ecoboost fusion
http://www.ecoboostperformanceforum.com/index.php/topic,1283.msg56765.html#msg56765 (http://www.ecoboostperformanceforum.com/index.php/topic,1283.msg56765.html#msg56765)

(http://i102.photobucket.com/albums/m113/Ford-man77/bigturbovdyno_zps49a9ba0d.jpg)
(http://i102.photobucket.com/albums/m113/Ford-man77/BigTurboLog9-13-14_zpscc039af3.jpg)

From the sig:
-Fswerks (Randy) 93 oct. tune, -OCD Speed 3" downpipe,
-straightline performance 3" cbe, -levels performance 2.5" hot side charge pipe,- straightline performance 3" turbo inlet pipe, -steeda air box replacement -ATP FMIC upgrade
-Eibach sport springs -steeda sway bar-snow performance water meth kit
Title: Re: Dyno Results
Post by: FoMoCoSHO on September 14, 2014, 10:10:44 PM
Randy is a good guy, he left FS WERKS and went to Mountune USA. I'm anxious to see if Ford extends warranty support to them as they do in Europe.
Title: Re: Dyno Results
Post by: SHOdded on October 07, 2014, 05:41:51 AM
rjdkanak's 2012 SHO:
http://www.ecoboostperformanceforum.com/index.php/topic,3776.msg58834.html (http://www.ecoboostperformanceforum.com/index.php/topic,3776.msg58834.html)

(http://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=3776.0;attach=4915;image)

Upgrades - 93 Torrie tune, 3bar MAP, Snow Stage 1 at 8lbs, SP534's, 170tstat, resonator straight piped, dynomax axle back.
Downsides - K&N CAI(sounds sweet!), stock downpipes, 3rd cat.
Title: Re: Dyno Results
Post by: SHOdded on November 28, 2014, 08:02:21 PM
91hybrid's 2014 SHO -PP:
http://ecoboostperformanceforum.com/index.php/topic,4049.msg63271.html#msg63271 (http://ecoboostperformanceforum.com/index.php/topic,4049.msg63271.html#msg63271)

(http://tapatalk.imageshack.com/v2/14/11/28/73a6e5b852be4d24c3164181eeabdbc8.jpg)
2014 Ford Taurus SHO dyno 418 hp- 513 lb/ft! (http://www.youtube.com/watch?v=uGbBb4Z92oE#ws)

Unleashed Tuned, 3bar, Devils Own 100% meth, PPE catted down pipes, 3rd cat delete, Magnaflow 2.5" exhaust, 170 deg, NGK 7's plugs
418 whp - 513 wlb/ft
Title: Re: Dyno Results
Post by: SHOdded on December 02, 2014, 11:17:53 PM
SHO-TYM's 2011 SHO:
http://www.ecoboostperformanceforum.com/index.php?topic=4068.msg63517#msg63517 (http://www.ecoboostperformanceforum.com/index.php?topic=4068.msg63517#msg63517)

2011 Ford Taurus SHO Dyno Run (http://www.youtube.com/watch?v=rCfdkMxNFGI#ws)
Dyno graph at 0:25 mark
(http://tapatalk.imageshack.com/v2/14/12/02/4a89fa4f2359e48cd8aa0b0ed47239aa.jpg)

2011 Ford Taurus SHO non PP, Airaid intake, LMS Stage 4+X tune, 160* thermostat, new motorcraft plugs gapped at .030. 3 Bar Map Sensor, LMS non-catted down pipes
Title: Re: Dyno Results
Post by: SHOdded on January 22, 2015, 04:08:38 PM
Glassman710's 2013 PP SHO:
http://www.ecoboostperformanceforum.com/index.php/topic,4258.msg66183.html#msg66183 (http://www.ecoboostperformanceforum.com/index.php/topic,4258.msg66183.html#msg66183)

(http://www.ecoboostperformanceforum.com/gallery/60_22_01_15_2_07_37.jpeg)
(http://www.ecoboostperformanceforum.com/gallery/60_22_01_15_2_07_54.jpeg)

MODS:
Corsa cat back exhaust, K&N drop in filter, and 2 bar Unleashed 93octane Tune by Torrie
Title: Re: Dyno Results
Post by: SHOdded on February 03, 2015, 07:14:19 PM
peppelepugh's 2011 SHO (non-PP):
http://www.ecoboostperformanceforum.com/index.php/topic,4326.msg67104.html#msg67104 (http://www.ecoboostperformanceforum.com/index.php/topic,4326.msg67104.html#msg67104)

MDesign Intake:
(http://www.ecoboostperformanceforum.com/gallery/60_03_02_15_5_12_39.jpeg)
Airaid Intake:
(http://www.ecoboostperformanceforum.com/gallery/60_03_02_15_5_13_02.jpeg)

2011 Kona Blue SHO non-PP: AirAid CAI, All interior lights LEDs, LED Puddles, and LED Reverse.
EBC Stage 4 Brake kit. 170*, 3-Bar, NGK Plugs, and Tune by Torrie!
Title: Re: Dyno Results
Post by: bpd1151 on February 06, 2015, 05:35:02 PM
Quote from: SHOdded on August 09, 2014, 11:32:23 AM
bpd1151's 2010 Taurus SHO after Livernois Motorsports Buildout 8/9/2014

World's highest horsepower EcoBoost Taurus SHO by Livernois Motorsports (http://www.youtube.com/watch?v=WSlvKcG3neo#ws)
(http://www.ecoboostperformanceforum.com/gallery/60_09_08_14_8_31_32.jpeg)

To Quote:

Pro-Series Longblock engine that includes:
Livernois Motorsports Proprietary fully coated Pistons
Livernois Motorsports Proprietary Billet Connecting Rods
Livernois Motorsports Proprietary Main Studs
Livernois Motorsports Proprietary Head studs
Livernois Motorsports Ported Cylinder heads


Just thought I'd share with the community, that my engine build (from Livernois Motorsports) was highlighted in this month's "Street Legal TV" newsletter.....

A further in depth article that breaks down the services performed. Kind of cool stuff!

Click on the third link down that features 3.5 Ecoboost build for more info......

http://list.powerautomedia.com/index.php?action=social&chash=68a9750337a418a86fe06c1991a1d64c.3305 (http://list.powerautomedia.com/index.php?action=social&chash=68a9750337a418a86fe06c1991a1d64c.3305)
Title: Re: Dyno Results
Post by: SHOdded on February 07, 2015, 04:24:54 PM
myshoisfast's 2013 SHO:

(http://www.ecoboostperformanceforum.com/gallery/60_07_02_15_2_23_25.jpeg)

Tunes included with the Diablosport InTune 1-1000 tuner
Title: Re: Dyno Results
Post by: SHOdded on March 30, 2015, 02:50:28 AM
A quick How & Why on Dynos from Ford Racing:
http://www.fordracingparts.com/download/tipsPDF/EnginePerformanceTechTips.pdf (http://www.fordracingparts.com/download/tipsPDF/EnginePerformanceTechTips.pdf)
Title: Re: Dyno Results
Post by: FoMoCoSHO on March 30, 2015, 10:33:30 PM
Quote from: SHOdded on February 07, 2015, 04:24:54 PM
myshoisfast's 2013 SHO:

(http://www.ecoboostperformanceforum.com/gallery/60_07_02_15_2_23_25.jpeg)

Tunes included with the Diablosport InTune 1-1000 tuner
That's a canned tune?
Title: Re: Dyno Results
Post by: SHO-TYM on April 20, 2015, 03:40:22 PM
Here is my Dyno Sheet:
2011 Ford Taurus SHO non PP, Livernois Motorsports Windstorm Intake, Custom LME Methanol Tune, 160* thermostat, new motorcraft plugs gapped at .028. 3 Bar Map Sensor, LMS non-catted down pipes, Corsa Catback System, ALKY Methanol Injection
Title: Re: Dyno Results
Post by: AJP turbo on April 20, 2015, 04:04:52 PM
Sho tym how much boost and what year was that dyno pull done in?
Title: Re: Dyno Results
Post by: SHOdded on June 05, 2015, 07:44:49 AM
BOOSTD SHO's 2013 SHO:

Record-breaking run at Milan, MI - May 2015
! No longer available (http://www.youtube.com/watch?v=EyNCsuWg_Aw#)
Dyno Chart:
(http://www.ecoboostperformanceforum.com/gallery/60_05_06_15_4_43_19.jpeg)

SETUP:
Livernois Motorsports Pro-Series Shortblock / Livernois Motorsports Stage 1 Cylinder head upgrade / Livernois Motorsports Exclusive Head studs / Livernois Motorsports Exclusive Main studs / Livernois Motorsports Exclusive Bore Support System / Livernois Motorsports Methanol Injection System / Livernois Motorsports Custom MyCalibrator Tuner / Livernois Motorsports EvenFlo Thermostat /Livernois Motorsports 3-Bar Map sensor upgrade / Livernois Motorsports Thunderstorm Downpipes / Livernois Motorsports Thunderstorm Cat-Back / Livernois Motorsports Spec'd Upgraded Turbos by ATP​
Title: Re: Dyno Results
Post by: pejohnson on June 05, 2015, 03:18:50 PM
It was exciting to be there and see it in person.
Title: Re: Dyno Results
Post by: gad on June 09, 2015, 02:11:03 PM
update time on drag time database.
Title: Re: Dyno Results
Post by: irondoor19 on June 19, 2015, 10:49:21 AM
AND ON A HAPPY NOTE:  ;D

Added a 3Bar, New Regapped Plugs, Lower Temp Thermostat & MDesign Air Intake

4 Hours of Dyno Time (90 Deg Plus Day) and a bit of heat Soak, Here are the results:

386 HP (from Last years 368)  478 FT LB's (from Last years 424) Yikes


Title: Re: Dyno Results
Post by: SHOnUup on June 20, 2015, 07:28:21 AM
Nice #'s you're sporting!

Rich

Title: Re: Dyno Results
Post by: SHOdded on November 11, 2015, 12:20:24 AM
kyle04's 2014 SHO:

(http://i.imgur.com/Lix5MWE.jpg)

SETUP:
Livernois tune, 3bar MAP, TStat, Downpipes
Title: Re: Dyno Results
Post by: SHOdded on June 01, 2016, 05:58:28 AM
SpeedTrap's 2013 PI Sedan ECOBOOST:

Mustang Dyno
(http://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=6266.0;attach=10794;image)

http://www.ecoboostperformanceforum.com/index.php/topic,6266.msg97448.html#msg97448 (http://www.ecoboostperformanceforum.com/index.php/topic,6266.msg97448.html#msg97448)

Mods: Airaid CAI, 3 Bar MAP, plugs, 170 degree thermostat, HP tuners
Title: Re: Dyno Results
Post by: SHOdded on August 25, 2016, 05:47:36 PM
clubfit's 2015 SHO w/ PP:

(http://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=6611.0;attach=11424;image)

http://www.ecoboostperformanceforum.com/index.php/topic,6611.msg102597.html#msg102597 (http://www.ecoboostperformanceforum.com/index.php/topic,6611.msg102597.html#msg102597)

2015 SHO PP. Every option; BREW CITY BOOST TUNE; 3RD CAT DELETE; 170* THERMOSTAT; H&R SPRINGS
Title: Re: Dyno Results
Post by: SHOdded on December 25, 2016, 07:25:34 AM
MiWiAu's 2013 Explorer Sport:

(http://i1076.photobucket.com/albums/w449/mauskings/Dyno%20Charts%20-%2023DEC16/Overall%20Tune%20Comparison_zpsxotg8pxo.png)
(http://i1076.photobucket.com/albums/w449/mauskings/Dyno%20Charts%20-%2023DEC16/Total%20Power%20Comparison%20Area%20Plot_zpsynrmydn6.png)

Full thread here:
http://www.ecoboostperformanceforum.com/index.php/topic,6919 (http://www.ecoboostperformanceforum.com/index.php/topic,6919)

2013 XPL0DR Sport
AJP Turbo Tuned
NGK 6510 Plugs (0.030"), 170 degree RAT Stat, AEM DryFlow Filter, AJP Turbo Boost Regulator, Lubed with AMSOIL
Title: Re: Dyno Results
Post by: jims2015 on December 25, 2016, 11:27:42 PM
(http://i51.photobucket.com/albums/f359/46628/dyno2_zpsaxaqu5lt.jpg)

15PP, Thunderstorm catted DP, Windstorm CAI, AlkyControl, Livernois dyno tune, stock cat back and stock mufflers.
Title: Re: Dyno Results
Post by: nelsonbullitt on December 26, 2016, 01:57:11 PM
Quote from: jims2015 on December 25, 2016, 11:27:42 PM
(http://i51.photobucket.com/albums/f359/46628/dyno2_zpsaxaqu5lt.jpg)

15PP, Thunderstorm catted DP, Windstorm CAI, AlkyControl, Livernois dyno tune, stock cat back and stock mufflers.

That's amazing! Jim, can you elaborate on your mods?
Title: Re: Dyno Results
Post by: AJP turbo on December 26, 2016, 02:52:10 PM
Thats meth iniected?
Title: Re: Dyno Results
Post by: jims2015 on December 27, 2016, 04:04:46 AM
Quote from: nelsonbullitt on December 26, 2016, 01:57:11 PM
Quote from: jims2015 on December 25, 2016, 11:27:42 PM
(http://i51.photobucket.com/albums/f359/46628/dyno2_zpsaxaqu5lt.jpg)

15PP, Thunderstorm catted DP, Windstorm CAI, AlkyControl, Livernois dyno tune, stock cat back and stock mufflers.

That's amazing! Jim, can you elaborate on your mods?


Sure, other than what I have listed, what would you like to know? I'm sure the exhaust is choking it down some, but the older I get, the quieter I like it.
Title: Re: Dyno Results
Post by: jims2015 on December 27, 2016, 09:49:21 AM
Quote from: AJP turbo on December 26, 2016, 02:52:10 PM
Thats meth iniected?

100% VP M-1
I haven't spoken to the dyno tuner yet but I suspect mine is a little conservative. It's been 6 months of driving now and I haven't even used 2 gallons yet. I even bought an extra 5 gallon pail expecting the use rate to be much higher.
Title: Re: Dyno Results
Post by: derfdog15 on January 10, 2017, 07:56:09 PM
derfdog's 2015 SHO w/ PP:

(http://i.imgur.com/hF84Ia7.jpg)

Runs 1, 2, and 3 are tuned power pulls, run 4 is "baseline/stock tune" optimized for my mods but with no addition spark and no addition boost.

2015 SHO w/ PP; 20x8.5 Black AMR wheels all around; All chrome blacked out; Resonator delete & OE Mufflers replaced with welded X-Pipe & Summit Race Mufflers; Airaid CAI; 3 Bar MAP; Reische 170 T-stat; EPP Hotpipes with custom AJP Boost Regulator(MV-S 38mm Wastegate); Stainless Works Catless Downpipes; AJPTurbo Tune

Full thread: http://www.ecoboostperformanceforum.com/index.php/topic,7289.0.html (http://www.ecoboostperformanceforum.com/index.php/topic,7289.0.html)
Discussion starts here:
http://www.ecoboostperformanceforum.com/index.php/topic,7171.msg111088.html#msg111088 (http://www.ecoboostperformanceforum.com/index.php/topic,7171.msg111088.html#msg111088)
Title: Re: Dyno Results
Post by: SHOdded on February 20, 2017, 10:25:22 PM
f8tlsho's 2013 SHO non PP:

(https://uploads.tapatalk-cdn.com/20170220/0a0388964594dac461345ff3a9fcc8c3.jpg)
E20 15psi,14psi, stock w/E20 - mustang dyno

2013 Non PP Unleashed 93 E20 3 Bar Tune, K&N drop in ; Tuned 12.491 @ 110.96 120's IAT
Now tuned by ajp...looking to go faster - 3 Bar 93 E20 - 12.59 @110 160's IAT

Full thread:  http://www.ecoboostperformanceforum.com/index.php/topic,7473 (http://www.ecoboostperformanceforum.com/index.php/topic,7473)
Title: Re: Dyno Results
Post by: SHOdded on April 12, 2017, 09:50:37 AM
TopherSHO's 2010 NON-PP SHO:

Mustang Dyno
(http://i66.tinypic.com/28jfwhs.jpg)
http://www.ecoboostperformanceforum.com/index.php/topic,6287.msg116387.html#msg116387 (http://www.ecoboostperformanceforum.com/index.php/topic,6287.msg116387.html#msg116387)

3-bar,  .028 NGK plugs, AJP TURBO 92-Pump tune (rev10), crappy goodyear tires.
Title: Re: Dyno Results
Post by: TopherSho on April 13, 2017, 10:46:53 AM
Quote from: SHOdded on April 12, 2017, 09:50:37 AM
TopherSHO's 2010 NON-PP SHO:

Mustang Dyno
(http://i66.tinypic.com/28jfwhs.jpg)
http://www.ecoboostperformanceforum.com/index.php/topic,6287.msg116387.html#msg116387 (http://www.ecoboostperformanceforum.com/index.php/topic,6287.msg116387.html#msg116387)

3-bar,  .028 NGK plugs, AJP TURBO 92-Pump tune (rev10), crappy goodyear tires.

I'd amend the posting style 'slightly' as a suggestion.  If available i would include spark data, it is a interesting data-point to have.
Title: Re: Dyno Results
Post by: SHOdded on April 13, 2017, 12:08:04 PM
Yeah I could but then people would ask for other datapoints :)  Besides, the link to the original post is provided.  Not ideal, but then you have context for that dyno that way.
Title: Re: Dyno Results
Post by: TopherSho on April 16, 2017, 07:18:06 PM
RGR that!!
Title: Re: Dyno Results
Post by: SHOdded on May 26, 2017, 06:44:12 PM
ZSHO's 2013 Performance Package SHO

Before & After DPAMI

(https://i.imgur.com/jjJ6tO6h.jpg)


Mods:  Livernois Custom Methanol Tune|3-Bar Map|Reische-170-Stat|Full Race Tial-8psi BOV|PPE-Gloss Black Hot Pipes|PPE Catted DP|Corsa Cat Back Exhaust|H&R Sport-Springs|Airaid-Dry-flow-CAI|RX Front clean side oil Separator|Llumar 20%Ceramic window Tint|Extreme Roof Spoiler|First-SHO With Direct Port Alky-VP-M1-100%-Methanol Injection|LMS-Custom-Dyno-Tuned @ 415whp-465wtq|
Title: Re: Dyno Results
Post by: ZSHO on May 26, 2017, 09:34:10 PM
-MANU Thank you kind sir!!. Z  :)
Title: Re: Dyno Results
Post by: SHOdded on July 21, 2017, 02:33:11 PM
hawkeye93's 2015 Performance Package SHO

BCB E30 tune, Mustang Dyno
(https://uploads.tapatalk-cdn.com/20170721/bb1c0a251f8219cda8e652026c73ada6.jpg)

2015 Ford Taurus SHO PP 12.316@112.58
LMS catted DP, AirAid CAI, SP-534, Reische 170, 3 bar, hybrid meth system, tunes from Unleashed, Livernois, Brew City Boost & AJP
Title: Re: Dyno Results
Post by: Macgyver on July 21, 2017, 10:57:35 PM
So 424tqe and 380whp ?
Title: Re: Dyno Results
Post by: SHOdded on October 23, 2017, 06:04:07 PM
ddlopes's 2013 Performance Package SHO

AJP Meth tune, on a Dynojet
(https://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=8478.0;attach=16006;image)

2013 SHO P/P
mods: Airaid, 3 bar, PPE catted down pipe, SCT X4, 170 degree thermostat, SNOW PERFORMANCE methanol stage 3, AeroForce gauges, Hot pipes, custom boost activated cutout xpipe, tial bov, Tial Wastegate mod, AJP tune and Rovos Durban wheels
Title: Re: Dyno Results
Post by: SHOdded on February 26, 2018, 06:40:30 PM
arrivalblue's 2013 MKS

K&N dropin filter only
(https://uploads.tapatalk-cdn.com/20180226/a134ba06e8781cac86bc2d6f78f33a75.jpg)
(https://uploads.tapatalk-cdn.com/20180226/5c3a14d8daf1b1630430f6e4a929b9c3.jpg)
Title: Re: Dyno Results
Post by: Macgyver on February 26, 2018, 07:36:54 PM
So maybe 3 whp and wtq over the stock filter on a 2013 MKS ? Untuned and just dropped in?
Title: Re: Dyno Results
Post by: AJP turbo on February 26, 2018, 08:01:58 PM
I guess it's acting as it should ...in theory you should not see any power increase from an intake since the stock tune is targeting a torque value . So you would have to monitor boost and the stock tune would run less boost and see the same power

The car knows the torque so if you are making more because the hardware is more efficient then the ecu would lower the boost targets
Title: Re: Dyno Results
Post by: Macgyver on February 27, 2018, 12:05:23 AM
Sounds like Nissan Jukes. You can bolt on everything that should make more power. Sans a new Turbo. The ECU nerfs it. Thats why we tune.
Title: Re: Dyno Results
Post by: ZSHO on July 05, 2018, 08:53:49 PM
5ohSHO  2018 PP-SHO
405hp/447tq.

(https://i.imgur.com/A77ytLZh.jpg?3)

2018 SHO Velvet Burgundy w/PP. MDesign CAI, 3 bar map, MSD coils, .30 plugs, 160 t-stat, Thunderstorm cat-less dp's, Corsa cat-back, Alky Control meth injection, EPP Hot Pipes, Dyno tune, H&R springs and Advanti Hybris wheels.

405hp/447tq.
Title: Re: Dyno Results
Post by: SHOdded on July 27, 2018, 05:24:21 PM
Night Hawk's 2017 Fiesta ST

A 93 tune nets these results!
(https://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=9334.0;attach=18461;image)
(https://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=9334.0;attach=18463;image)

https://www.ecoboostperformanceforum.com/index.php/topic,9334 (https://www.ecoboostperformanceforum.com/index.php/topic,9334)

2017 Fiesta ST
Black/ black rims
Mountune MM/intake FMIC, Quickshift
CFM breather/catch can LMS 93 tune
191whp/245wtq SAE
Title: Re: Dyno Results
Post by: Macgyver on July 28, 2018, 12:41:48 AM
Pretty good for a 1 litre
Title: Re: Dyno Results
Post by: shoNoff on July 28, 2018, 08:41:34 AM
Some impressive torque from that little motor. I bet that fiesta screws. What do they dyno stock? Just curious.
Title: Re: Dyno Results
Post by: SHOdded on August 16, 2018, 04:53:14 PM
5OhSHO's 2018 SHO

With upgraded CHRA's!
(https://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=299.0;attach=18717;image)

https://www.ecoboostperformanceforum.com/index.php/topic,299.msg141238.html#msg141238 (https://www.ecoboostperformanceforum.com/index.php/topic,299.msg141238.html#msg141238)

2018 SHO Velvet Burgundy w/PP. MDesign CAI, 3 bar map, MSD coils, .30 plugs, 160 t-stat, Thunderstorm cat-less dp's, Corsa cat-back, Alky Control meth injection, EPP Hot Pipes, Upgraded CHRA's, Turbo Smart WGA's, Dyno tune, H&R springs and Advanti Hybris wheels.

486whp/488wtq.
Title: Re: Dyno Results
Post by: SHOdded on April 04, 2019, 07:14:23 AM
76FoMoCo's 2013 PP SHO:

55o 2500 alt 60% humidity on a mustang AWD

(https://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=2059.0;attach=19983;image)

https://shoforum.com/index.php?threads/lms-vs-gearhead-canned-tunes-comparison.138578/page-19#post-1507767 (https://shoforum.com/index.php?threads/lms-vs-gearhead-canned-tunes-comparison.138578/page-19#post-1507767)

2013 PP LMS 93 V11+meth 160 TS plugs, 3 bar, LMS catch can, EPP catted DP's, bridgestone potenza s007a
Title: Re: Dyno Results
Post by: SHOdded on April 24, 2019, 04:49:27 PM
StealBlueSHO's 2016 PP SHO

(https://uploads.tapatalk-cdn.com/20190424/2402bf2f6a10db8b077e32bd1ae5b3e2.jpg)
Uncorrected
(https://uploads.tapatalk-cdn.com/20190424/0a2b3c38efa69a17586ac0178bd84c36.jpg)

(Not yet tuned for the turbos/hotpipes, running a base tune only)

https://youtu.be/b1xjQSkiGmQ (https://youtu.be/b1xjQSkiGmQ)

Follow the build thread here:
https://www.ecoboostperformanceforum.com/index.php?topic=9894 (https://www.ecoboostperformanceforum.com/index.php?topic=9894)

2016 Taurus SHO PP, Gearhead Tuned, XDI HPFP, Gearhead Intercooler, Corsa Exhaust, HR Springs, Airaid Intake, EPP Hotpipes, 160Tstat, 3BAR Map, LMS Catch Can, Upgraded Torque Mounts, SP-542's, Gearhead Turbo Upgrades and EPP Catted Downpipes
Title: Re: Dyno Results
Post by: 76fomoco on May 16, 2019, 05:29:04 PM
AJP 93+meth 58 deg 77% humidity with the DA at 4020' on 1/3 of the meth LMS was using. on a mustang dyno with all the same mods as a few post back
Title: Re: Dyno Results
Post by: SHOdded on May 16, 2019, 07:20:58 PM
LMS93 dyno run a couple of posts above
https://www.ecoboostperformanceforum.com/index.php/topic,2059.msg148328.html#msg148328 (https://www.ecoboostperformanceforum.com/index.php/topic,2059.msg148328.html#msg148328)
Title: Re: Dyno Results
Post by: 76fomoco on May 16, 2019, 11:42:18 PM
I would MOST definitely work with AJP again he is an awesome communicator and takes the time to make it right. NOT a one hit wonder and you will have to do your part to get logs to him.
Title: Re: Dyno Results
Post by: SM105K on May 17, 2019, 09:14:37 AM
Quote from: 76fomoco on May 16, 2019, 11:42:18 PM
I would MOST definitely work with AJP again he is an awesome communicator and takes the time to make it right. NOT a one hit wonder and you will have to do your part to get logs to him.

Nice numbers, can't wait to see what you do at the track....
Title: Re: Dyno Results
Post by: 76fomoco on August 13, 2019, 05:05:21 PM
E30 tune by AJP 3700 feet DA at 70*. Run number one was my meth tune file loaded (for comparison)  Run 2 and 3 where the E30 Tune
Title: Re: Dyno Results
Post by: 802SHO on August 13, 2019, 05:51:57 PM
Quote from: 76fomoco on August 13, 2019, 05:05:21 PM
E30 tune by AJP 3700 feet DA at 70*. Run number one was my meth tune file loaded (for comparison)  Run 2 and 3 where the E30 Tune

Very nice!  Is the meth tune with 93 or is it e30+ meth? 
Title: Re: Dyno Results
Post by: 76fomoco on August 13, 2019, 06:07:57 PM
93 with meth.
Title: Re: Dyno Results
Post by: SHOdded on February 05, 2020, 12:27:42 AM
ddlopes 2013 SHO with Perf Pkg:

Dyno results on Boostane Professional
(https://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=10331.0;attach=22290;image)
vs E30
(https://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=10331.0;attach=22292;image)

Setup:
EcoPower Parts dual CAI, 3 bar, PPE catted down pipe, SCT X4, 170 degree thermostat, SNOW PERFORMANCE methanol stage 3 with ProMeth staineless steel braided lines, AeroForce gauges, Hot pipes, custom boost activated cutout xpipe, tial bov, Tial Wastegate mod, GH intercooler, MSD coils, AFE throttle spacer, UPR catch can, Rovos Durban wheels, AJP tuned to 389hp and 503trq on mustang dyno
Title: Re: Dyno Results
Post by: SHOdded on February 06, 2020, 08:39:35 AM
Jordan's 2013 SHO (https://www.ecoboostperformanceforum.com/index.php/topic,10334.msg156192.html#msg156192)

AJPturbo tuned:
(https://i.imgur.com/cIR5Ks9.jpg)

Gearhead tuned:
(https://i.imgur.com/YCgOUfN.jpg)

AJPTURBO AND GEARHEAD TUNED - XDI35 HPFP, Gearhead Intercooler, Anthony Dicunzolo trans mounts, J2 Dual Intake, PPE catless downpipes, MSD coils, full exhaust, Ebay compressor wheels
Title: Re: Dyno Results
Post by: SHOdded on March 15, 2020, 01:00:24 AM
Jordan's 2013 SHO (https://www.ecoboostperformanceforum.com/index.php/topic,10391)
Now with GH turbos!

(https://www.ecoboostperformanceforum.com/index.php?action=dlattach;topic=2059.0;attach=22524;image)

AJPTURBO AND GEARHEAD TUNED - XDI35 HPFP, Gearhead Turbos, Gearhead Intercooler, Anthony Dicunzolo trans mounts, J2 Dual Intake, PPE catless downpipes, MSD coils, full exhaust, Ebay compressor wheels
Title: Re: Dyno Results
Post by: 76fomoco on September 13, 2020, 11:48:06 AM
the first one is no meth and the second is with meth. all mods are in my signature
Title: Re: Dyno Results
Post by: StealBlueSho on September 13, 2020, 12:12:30 PM
Quote from: 76fomoco on September 13, 2020, 11:48:06 AM
the first one is no meth and the second is with meth. all mods are in my signature


Holy crap those are some serious numbers!!!!!! Congrats on the dyno and thank you for sharing! Those are some sexy curves! When's the next track day?
Title: Re: Dyno Results
Post by: 76fomoco on September 13, 2020, 12:28:43 PM
2-3 weeks.
They are on the same mustang dyno I started with
Title: Re: Dyno Results
Post by: 802SHO on September 13, 2020, 01:40:22 PM
Quote from: 76fomoco on September 13, 2020, 11:48:06 AM
the first one is no meth and the second is with meth. all mods are in my signature
Looking forward to your next track attack!!!  Sweet numbers!  11's all day street and track


Sent from my iPhone using Tapatalk
Title: Re: Dyno Results
Post by: ridered74 on September 13, 2020, 11:57:32 PM
Dang even more impressive on a mustang dyno.
EhPortal 1.39.5 © 2024, WebDev