September 24, 2023, 08:03:09 PM

Author Topic:  Add-A-Fuse Fuse Tap  (Read 8922 times)

Offline Bigjht

  • Jr. Member
  • *
  • NW Arkansas
  • Thank You
  • -Given: 0
  • -Received: 0
  • Posts: 24
  • Ecobooster
  • Liked:
  • Likes Given: 0
Add-A-Fuse Fuse Tap
« on: February 09, 2014, 07:53:27 PM »
Does anyone on here have experience with the fuse taps?  I'm looking to install a 12 volt auxiliary power outlet in the tray on my dash to house a dual 2.4 amp USB charger, which will power my Nexus 7 and any other tablet/phone I may need to charge.  My concern is the stock 12 volt auxiliary outlets on the truck run to a 20 amp fuse, but this will only go up to 10 amp max.  I found some cheaper ones that say 15 and 20 amp max but they seem to be utilizing the same 16 gauge wiring so I don't quite trust those.  I only intend to use this for the tablet and phone charging so with the usb adapter I should only max out at 4.8 amps anyway if I'm charging 2 tablets at the same time.  With that being said, from my readings and limited knowledge of the subject, I should be ok then as long as I don't take the USB Adapter out and put something that would draw more amps right?  I see some unused fuse slots that I'm hoping I'll be able to plug in to but if they aren't hot on switch only I should still be able to utilize the rear heated seat fuse, which is 10 amps as well.  I mainly want to use this so I don't have to splice in to any wiring.  Any advice or does all of this sound correct?
2013 PP SHO - Airaid CAI, Eibach Springs, Livernois Tune
2013 EB F150 Limited - Stock for Now!

Offline Mikesb

  • Full Member
  • *
  • Thank You
  • -Given: 0
  • -Received: 3
  • Posts: 148
  • Ecobooster
  • Liked:
  • Likes Given: 0
Re: Add-A-Fuse Fuse Tap
« Reply #1 on: February 09, 2014, 08:57:10 PM »
I just went round and round with the subject. What I ended up doing is using the type of tap that hooks through and to the bottom of the desired fuse. That way you can draw off of the hot side of the fuse you are tapping into without interfering with any of the existing fuses functions. Then your tap has its own independent fuse. One of the main things is to pick the rite fuse to use

Take what is say with a grain, that's just what I did on my own

Offline Larrylu

  • Elite Member
  • *
  • Albany, NY
  • Thank You
  • -Given: 11
  • -Received: 110
  • Posts: 717
  • Liked:
  • Likes Given: 0
Re: Add-A-Fuse Fuse Tap
« Reply #2 on: February 09, 2014, 10:05:20 PM »
That is what I did and it worked fine for me. I found and used an unused fuse at the panel under the dash on the drivers side that was hot on ignition on. I'm using it to power my Garmin and my Nexus. Nexus is powered through a 2.1 amp USB. I found that my vintage Nexus (previous to the current) needed a special USB (shorted data pins) to enable fast charge. Don't know if they still use that system or not. Go for it!
2010 Loaded, Non PP, Steel Blue Metallic, Livernois Stage 4+, Blacked out grill, Nexus 7 Tablet running Torque Pro

Offline dalum

  • Sr. Member
  • *
  • Central Ohio
  • Thank You
  • -Given: 15
  • -Received: 39
  • Posts: 250
  • All SHO and All GO
  • Liked:
  • Likes Given: 0
Re: Add-A-Fuse Fuse Tap
« Reply #3 on: February 09, 2014, 11:42:49 PM »
That tap is fine and its what I used.  Just make sure to test it with the factory fuse out so you know its not in backwards.
2013 Non-PP SHO


* Recent Topics

Re: My Staggered, TSW Wheel Setup.....
by dillrepair | September 23, 2023, 08:51:58 PM
Just wanted to say thanks to bpdHave the same setup bc of seeing this ...
Re: Body kits
by MKSJUNKIE | September 12, 2023, 10:23:45 PM
Sounds good I appreciate it. I...
Re: PTU Upgrade - Dorman
by BlueSHO | September 11, 2023, 10:46:17 AM
@timbo anything?Sent from my SM-G781V using Tapatalk...
Re: 2012 SHO PP
by bpd1151 | September 01, 2023, 08:25:20 PM
Pics are always helpful..... I mean c'mon now..... who doesn'...
Re: Fuel injector coding
by SHOdded | August 15, 2023, 01:38:53 PM
i would say to try new injectors then since fuel pump operation is goo...
Re: 315s?
by fsttyms1 | August 04, 2023, 03:40:50 PM
Thanks for the input guys. I did some reading around and even though b...
Re: bpd1151's 2010 SHO Rebuild Thread....
by kryptto | August 02, 2023, 09:12:14 PM
Just a quick update.....Went and visited the shop yesterday (07/21/202...
LH (Driver Side) Halfshaft Removal Tips?
by DaveBey | July 29, 2023, 09:54:27 PM
Does anyone have any tips for removing the LH (driver side) halfshaft?...
Re: New block, low oil pressure
by SHOdded | July 26, 2023, 01:56:20 PM
do you have an sho block or one from an explorer? their setups are sli...
Re: MSD Coils on 75% Sale
by SHOdded | July 26, 2023, 10:41:09 AM
feels like a closeout ... once gone, gone....

SimplePortal 2.3.5 © 2008-2012, SimplePortal