• Welcome to Ecoboost Performance Forum. Please log in or sign up.
collapse

Log Reading question

Started by SuperPete, January 12, 2020, 09:12:48 AM

Previous topic - Next topic

SuperPete

Reviewing my logs, few general question.
Fuel pump duty cycle and Fuel Pump percentage

Duty cycle, MIN 0.28 Max 0.48, what are these numbers? actual %? 28% to 48%?
fuel pump percentage, max going to 199.5%, is that possible?

these reading from my 1, 2, 3 gear pull

2014 SHO, GearHead TUNNED /Powered by Matt Robinson
PPE Downpipes, GearHead Intercooler, AirAid Intake
XDI-35 HPFP @ E40,   MSD Coilpacks
MUSTANG DYNO: 426/446
Continental Extreme Contact 06 & Powerstop Z23 all 4 corners

SuperPete

2014 SHO, GearHead TUNNED /Powered by Matt Robinson
PPE Downpipes, GearHead Intercooler, AirAid Intake
XDI-35 HPFP @ E40,   MSD Coilpacks
MUSTANG DYNO: 426/446
Continental Extreme Contact 06 & Powerstop Z23 all 4 corners

SHOdded

It's how Ford does things

QuoteWhat the Tech Says

A vehicle that has a fuel pressure port can be checked using a pressure gauge. This port may be at the rail or line, and you should look for pressure within the specifications of your vehicle. Additionally, the pressure should be tested under load by putting the car in gear or accelerating it. Should you find that the pressure is below specifications, look for a problem in one of the fuel lines. It could be bent or otherwise restricted.

A fuel filter that has not been changed can also be the cause of the restriction of fuel flow. The screens get dirty, so fuel filters need to be cleaned. If you have had any damage to the gas tank, it may be pressing into the fuel pump inlet.

The fuel pump driver module is operated on a pulse input signal from the ECM or PCM, and a pulse output signal that is sent to the pump. There may be a problem with the driver module, which could cause the wrong signal to be sent. You can check the module by using your wiring diagram and a DVOM. Set the DVOM to duty cycle, since that is what type of cycle the module uses, and put the negative lead on a good ground, and the positive lead on the signal wire.

The duty cycle will vary in relation to the commands sent from the PCM or ECM to the fuel pump. Ford doubles the duty cycle output, which means that a 30 percent input will give you a 60 percent output to the fuel pump. Fuel pump duty cycle will deliver this result. The PCM normally monitors the voltage, and there may be an additional DTC specifically for the pump driver module.

The problem may be in the fuel pressure sensor, which can be checked by using your wiring diagram and DVOM. The PCM typically monitors the voltage, and there will be a reference for this. You may see an additional code for a problem with the ground or power wires. It may set a P0190 code if there is a problem with the sensor circuit, and a P0191 code tells you there is a problem with the sensor circuit range or performance.

There may be an incorrect reading if there is excessive resistance within the sensor or wire leads. Use your DVOM in ohms scale, and check the pressure sensor's resistance by unplugging it and placing the negative and positive leads onto the sensor connector. Replace the sensor if the resistance is higher than specs. You can test the wiring by setting the DVOM to ohms scale and disconnecting the PCM and the sensor. Then check for excessive resistance between the wiring harness terminal ends with the negative lead on the end of the wiring harness and the positive DVOM lead on the other end of the harness.

https://www.bluespringsfordparts.com/blog/dtc-decoded-p0087
2007 Ford Edge SEL, Powerstop F/R Brake Kit, TXT LED 6000K Lo & Hi Beams, W16W LED Reverse Bulbs, 3BSpec 2.5w Map Lights, 5W Cree rear dome lights, 5W Cree cargo light, DTBL LED Taillights

If tuned:  Take note of the strategy code as you return to stock (including 3 bar MAP to 2 bar MAP) -> take car in & get it serviced -> check strategy code when you get car back -> have tuner update your tune if the strategy code has changed -> reload tune -> ENJOY!

SuperPete

2014 SHO, GearHead TUNNED /Powered by Matt Robinson
PPE Downpipes, GearHead Intercooler, AirAid Intake
XDI-35 HPFP @ E40,   MSD Coilpacks
MUSTANG DYNO: 426/446
Continental Extreme Contact 06 & Powerstop Z23 all 4 corners

FiveLeeter918

For duty cycle, double the number and that gives you it's overall capacity. If you reach 0.50, you're out of pump. Duty cycle and percentage are the same. One is just converted to a percentage.
- Lee
Technical Sales, Ortiz Tuning and Performance
F-150, Mustang, Lincoln MKS, Taurus SHO and Ford Flex Tuning

Ortiz Performance Vendor Forum | Find us on Facebook! | Shop Today!